[greenery_fr]

hi all,
just called me as shimi. i'm still new in this forum. i have TSUGAMI Model S16 Precision CNC Automatic Lathe. it use FANUC system. yesterday i was off the main swictch board for service and calibration. and also switch off the main switch of the machine. after finish the service, i switch on the machine and i got a lot of error on the screen. why it became like that.
310 APC ALARM : X AXIS NEED ZRN
320 APC ALARM : Z AXIS NEED ZRN
340 APC ALARM : 4 AXIS NEED ZRN
317 APC ALARM : X AXIS BATTERY DOWN 1
327 APC ALARM : Z AXIS BATTERY DOWN 1
347 APC ALARM : 4 AXIS BATTERY DOWN 1
350 APC ALARM : 5 AXIS NEED ZRN
360 APC ALARM : 6 AXIS NEED ZRN
357 APC ALARM : 5 AXIS BATTERY DOWN 1
367 APC ALARM : 6 AXIS BATTERY DOWN 1
490 SERVO ALARM : OVER LOAD
454 SERVO ALARM : 5 AXIS DETECT ERR
464 SERVO ALARM : 6 AXIS DETECT ERR

i also don't know where the battery. can somebody help me ASAP.

Hello

Could you tell me model of Fanuc controller

[injunear]

Salmve, if you tell me which 7 eproms you require I maybe able to supply them.

[salmve]

Sorry for delay. I have been busy and away from net.

Injunear, do you really have right program!
I need series 992 version 07 eprom numbers:
001G
002G
011F
022F
041F
111F
112F

Hope this helps.

Vekku

[yours_prabhat]

Mark
Thank you for offer of help, but this problem has already solved. Bubble memory has initialise and other board attached to masterboard has tested ok.

Main problem was 7 faulty eproms at the master. My eproms are series 992 version 07. I asked from Fanuc Sweden and they have version 08. I did not get prices yet, probably not very cheap. Suggestion of another way to get those eproms?

Are those version changeable without problem? (sure whole set of 26 eproms)

Vekku

I can send you the All programmed eproms Free of cost I have , I am not using that now

[yours_prabhat]

Hello

Could you tell me model of Fanuc controller

This problem are due to battery attached with controller only. Put the machine on for 4- 5 hours Idle in emergency than replace the suitable Battery only in power on condition these are APC alarm I think you have the Fanuc 0 M control . If still you confused feel free to communicate me Regards , Prabhat Mishra

[salmve]

I can send you the All programmed eproms Free of cost I have , I am not using that now

Thank you very much for offer of help, but problem has already solved.
I purchased whole new set of eproms from Injunear. Thanks.

Machine is now working condition.:wave:

Vekku

[yours_prabhat]

Hello

Could you tell me model of Fanuc controller

can any one send me the maintainance manual of Fanuc 6 T

[Abdullah]

When you initialize the buble memory you must switch "BMU switch " to ON position (NOT the parameter SW to enable) it's on upper side of the master print.

dear brother,
i need the maintince manual of fanuc 6t-b. my machine hitachi seiki 4ne3-600
had spindle problem its micon 8 PLC didnt generate proper voltage i need book to remove this fault

[Abdullah]

Hello
I purchaced old Nakamura TMC-3 with Fanuc 6t(b). It was out of order, so i get it at resonable price. I wired it up and turn mainswitch with shaking hands. All i get was "SYSTEM ERROR 9*" *-mark is strange symbol, looks like Japanese letter. Led number 1 lit on (master PCB) I have maintenence manual for this (Thanks Jonne) and i found out that it means alarm number 600. Maintenance manual has no remarks for this alarm.

I have read old post and found out that maybe i have to do some cleaning. First i will clean part programs, and then parameter data, and last totally cleanin of bubble memory. I have instructions for those. Is that right way? I think it is better to ask before than do something stupid, isn't it?

I have paper named "Setting of parameters" made by Nakamura. There is parameter numbers and data 0 to 160, 1001 to 1018, 2001, 2002 2101, 2102, and 3001 to 3004. Is that enough to get machine running if clening procedure get alarm away?

In the tape reader was tape without any marks what it is. Could it be machine parameter? But what a shame it is in two! But maybe it can repair and get reading.

Thanks in advance

Vekku

dear brother,
i also had hitachi seiki 4ne2-600 with fanuc system 6t-b i need its maintenance manual. if u had plzzzzzzzzzzzzzzzz give this manual

[snk]

For Fanuc manuals visit

CNC MANUALS

[fordav11]

you wont find any old Fanuc manuals online.....only from Fanuc 15B/Fanuc 16 and onwards are available in PDF format.

[jolulank]

Hate to hijack a thread but this is an emergency for me

Hello,

In my Mori Seiki SL1 with fanuc 6A I get a SYSTEM ERROR alarm 998 102 70 and I suppose it means the eeprom 102 and maybe line 70 because there is no eeprom 70

I hope you can help me.I need an EEPROM for fanuc 6A version 992. The EEPROM is 102F. I only need the file because I have an EEPROM reader/writer

Share or sell, your call

My email address [email protected] and whatsapp +52 1 811 662 1075

Thanks

jolulank