584,837 active members*
5,391 visitors online*
Register for free
Login
Results 1 to 8 of 8
  1. #1
    Join Date
    Mar 2004
    Posts
    847

    MDF Machine - Cut Aluminum?

    Just a quick question. Can a well made CNC machine using servos and a good router, but built from MDF, handle milling Alum?

    See, I was thinking of ordering high-quality parts (Servos, Gecko drivers, Ballscrews and Linear Rails) for my machine, but saving some initial cost by building it out of MDF. I have a few reasons for this:

    1) MDF is easy to work.
    2) MDF is cheap enough that I can tinker with the design.
    3) If the MDF machine can cut Alum, I can use it to remake the machine from Alum once my design is final.

    So, any thoughts?

  2. #2
    Join Date
    Mar 2003
    Posts
    332
    Maybe,
    My machine was bought. Made of tubular steel frame for stand and aluminum plate and extrusions for the machine itself. I usually use it for contouring graphite for glass molds. As sturdy as it is, it's still a challenge to get good work in aluminum. No match for a proper mill.
    Attached Thumbnails Attached Thumbnails route002.jpg  

  3. #3
    Join Date
    Mar 2004
    Posts
    847
    Quote Originally Posted by keithorr
    As sturdy as it is, it's still a challenge to get good work in aluminum. No match for a proper mill.
    Is that more of the Servos/Steppers and/or drive system problem or a construction problem though??

  4. #4
    Join Date
    Mar 2003
    Posts
    332
    The machine is too light. The position accuracy or motive power is not a problem, but vibration is. If I mill aluminum plate with an appropriate 1/4" end mill, I can get pretty good cuts. I can't hog anything and the swirl marks in finish cuts is more than you would get with a good mill. The router bearings aren't up to the job, and the 12" Z axis isn't rigid enough when extended. I have to use a tall fixture block to raise the workpiece so the Z axis is only hanging down a couple of inches. The uprights are of 1" aluminum plate, the crossmember is 6" square tube. The base plate is 1/2" aluminum plate with 5/8" plate rabbited on edge and screwed to the base to form T-slots. The ballscrews are rolled.

    I cut dry just to keep the machine clean. I could probably get better results with proper coolant. I don't think you would want to use coolant with an MDF machine.

  5. #5
    Join Date
    Jan 2004
    Posts
    490
    Many of the members here have milled aluminum with their MDF machines. Balsaman is the only one that I can think of off hand. Good luck.
    Stop talking about it and do it already!!!!!

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)

  6. #6
    Join Date
    Jun 2004
    Posts
    487
    Hi. This is no claim to fame but I did most of my hard aluminum alloy cuts on a machine that was held together with a couple of 2x4s. I noticed that using the right cutting tool for aluminum, slow feedrate and, yes, WD40 meant that there was little load put on the frame. Now that I switched to 8020 extrusions, I'm cutting the same alloys at a much faster rate and the edges come out much smoother.

    Not to knock off MDF but when I cut it, I get tons of a fine 'talc' that gets everywhere including the screws, rails, lungs, etc. Check the 8020 forum out and post your frame requirements - maybe they can help you as they did with me.

    Later,
    JR

  7. #7
    Join Date
    Mar 2004
    Posts
    847
    I don't have a problem keeping the speed down to save some money initially. Once I start selling some parts, I can always upgrade the machine.

    So MDF will work if:
    1) Keep the ipms down.
    2) Use some sort of cutting fluid!
    3) Use the right bits (and keep them sharp!).

  8. #8
    Join Date
    Jun 2004
    Posts
    487
    I'd say so. See the video here when I cut my router's base. I used a plain PVC clamp I got from the hardware store to hold the router while cutting the real holder. Because the whole setup it was so flimsy and my then router was only 1/2 HP, I did that cut very slowly. But, it worked.

    Regards,
    Julio

Similar Threads

  1. Cut the MDF to create an CNC machine.
    By samsagaz in forum WoodWorking Topics
    Replies: 6
    Last Post: 07-23-2008, 05:20 AM
  2. My First CNC Machine, Mr. Chips
    By Mr.Chips in forum DIY CNC Router Table Machines
    Replies: 81
    Last Post: 02-10-2007, 04:04 PM
  3. MDF CNC Machine Progress
    By victorbl in forum CNC Wood Router Project Log
    Replies: 61
    Last Post: 03-27-2006, 04:39 AM
  4. new cheap mdf machine
    By Hobbiest in forum DIY CNC Router Table Machines
    Replies: 36
    Last Post: 02-25-2004, 05:54 AM
  5. Machine Tool Camp 4'x8' VS Cad Cut CNC 4'x8' Router
    By Trimix in forum DIY CNC Router Table Machines
    Replies: 6
    Last Post: 12-18-2003, 08:49 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •