[Goesman]

Hi am about at my wits end with dolphin and mach 3. every time i load a gcode in mach i get a zero radius arcline error. i was wondering if any one may have a post the will fix this problem. This is the simple code i have been trying to run i get the error for line 13. Thanks for any help.

Dan



( Produced :- 19:42:29 Tuesday, December 23, 2008 )
( CNC File :- CIRCLES )
( Post Processor :- M_MACH3 )
( Part Number ID :- )
N5G00G20G17G90G40G49G80
N6G49
N7T1M06 ( End mill )
N8G00G43Z1.9685H1
N9S500M03
N10G94
N11X0.75Y0.0
N12Z0.125
N13G01Z-0.25F1.25
N14G03X0.0Y-0.75I0.0J0.0F5.0
N15X-0.75Y0.0I0.0J0.0
N16X0.0Y0.75I0.0J0.0
N17X0.75Y0.0I0.0J0.0
N18G01X0.375Y0.0
N19G03X0.0Y-0.375I0.0J0.0
N20X-0.375Y0.0I0.0J0.0
N21X0.0Y0.375I0.0J0.0
N22X0.375Y0.0I0.0J0.0
N23G01X0.1875Y0.0
N24G03X0.0Y-0.1875I0.0J0.0
N25X-0.1875Y0.0I0.0J0.0
N26X0.0Y0.1875I0.0J0.0
N27X0.1875Y0.0I0.0J0.0
N28G00Z1.9685
N29X0.75Y0.0
N30Z-0.125
N31G01Z-0.5F1.25
N32G03X0.0Y-0.75I0.0J0.0F5.0
N33X-0.75Y0.0I0.0J0.0
N34X0.0Y0.75I0.0J0.0
N35X0.75Y0.0I0.0J0.0
N36G01X0.375Y0.0
N37G03X0.0Y-0.375I0.0J0.0
N38X-0.375Y0.0I0.0J0.0
N39X0.0Y0.375I0.0J0.0
N40X0.375Y0.0I0.0J0.0
N41G01X0.1875Y0.0
N42G03X0.0Y-0.1875I0.0J0.0
N43X-0.1875Y0.0I0.0J0.0
N44X0.0Y0.1875I0.0J0.0
N45X0.1875Y0.0I0.0J0.0
N46G00Z1.9685
N47M09
N48M30
%

[Goesman]

woo hoo

i figured it out. never mind.

Thanks, Dan

[selrahc]

Hi Dan,

How did you managed to fix it?

Sunmixed

[windy_miller]

Hi Guys,

I had exactly the same problem which affected circles over a certain size. In part it is due to floating point errors in the maths processor.


The solution is to modify the post so it interprets the arcs differently. I must admit to not doing this myself but those good folks at Dolphin modified the post for me, in a matter of minutes.

I have the new post if you need a copy.

BR,
Windy.