585,602 active members*
3,634 visitors online*
Register for free
Login
IndustryArena Forum > MetalWorking Machines > Fadal > serial-rs232 settings on 32MP Fadal VMC 6535-50

Thread: serial-rs232 settings on 32MP Fadal VMC 6535-50

Results 1 to 5 of 5
  1. 01-28-2009, 06:36 PM #1
    kputer
    kputer is offline Registered
    Join Date
    Mar 2005
    Posts
    13

    serial-rs232 settings on 32MP Fadal VMC 6535-50

    Hi everybody, I hope this is an easy question but no one in the shop knows:

    What Fanuc control is used in the 32MP on a Fadal VMC 6535-50? I'm trying to help them connect via rs232 to a laptop running CNCmax and all we know is the baud rate is set to 38400. I'm hoping to find what stop bits, parity, Xon/Xoff and so on. We get a short transfer with goofy characters so I think we're close.
    Thanks,
    Keith
    Reply With Quote Reply With Quote
  2. 01-28-2009, 07:38 PM #2
    DareBee
    DareBee is offline Monkeywrench Technician
    Join Date
    Jan 2004
    Posts
    3154
    7E1 Xon/Xoff
    www.integratedmechanical.ca
    Reply With Quote Reply With Quote
  3. 01-28-2009, 07:39 PM #3
    DareBee
    DareBee is offline Monkeywrench Technician
    Join Date
    Jan 2004
    Posts
    3154
    7E1 Xon/Xoff
    It is a Fadal 88HS control
    www.integratedmechanical.ca
    Reply With Quote Reply With Quote
  4. 01-28-2009, 10:23 PM #4
    kputer
    kputer is offline Registered
    Join Date
    Mar 2005
    Posts
    13
    Thanks, I'm closer because now it sends a few lines then quits. So it's not a fanuc control?
    Reply With Quote Reply With Quote
  5. 01-28-2009, 10:50 PM #5
    Neal
    Neal is offline Registered
    Send a message via AIM to Neal
    Join Date
    Mar 2003
    Posts
    900
    32 MP and the 88HS are the same settings for the RS-232. The RS-422 for the embedded PC is a different story.

    Neal
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. RS232 Settings for CNC Arrow 750
    By SSWELD in forum CNC (Mill / Lathe) Control Software (NC)
    Replies: 5
    Last Post: 08-27-2010, 07:46 PM
  2. OKUMA OSP-U10L RS232 SETTINGS
    By edmondyjh in forum Okuma
    Replies: 1
    Last Post: 09-25-2008, 08:13 PM
  3. Fadal 32MP Control
    By bigcrunch in forum Want To Buy...Need help!
    Replies: 3
    Last Post: 02-13-2008, 08:47 PM
  4. FADAL 32MP RS-422 Pin Config.
    By komplekx in forum Fadal
    Replies: 6
    Last Post: 10-23-2006, 06:07 PM
  5. rs232\serial port (Voltage)
    By j m in forum Computers / Desktops / Networking
    Replies: 5
    Last Post: 08-05-2005, 01:43 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules