584,863 active members*
4,813 visitors online*
Register for free
Login
IndustryArena Forum > Machine Controllers Software and Solutions > Mach Software (ArtSoft software) > Mach3 , Config, Motor Tuning problem ( FILM OF MOTOR)
Results 1 to 8 of 8
  1. #1
    Join Date
    Jun 2007
    Posts
    8

    Mach3 , Config, Motor Tuning problem ( FILM OF MOTOR)

    Hello All I Very Like Make a Little Cnc Machine
    but i have problem is to
    Please See The Picture Below

    Hardware
    -----------------
    I buy 3 Axis Stepping Motor (Start Shaphon 23HS3002)



    My Motor


    Buy 3 Step Driver (MS-2H057M) And Set It



    My Drive



    Buy Pmdx-122 and Set It




    Assembly In Box Below



    Buy Dc 9V Adaptor



    Conect Stepping Motor to conector





    Connect All To Box and Pc By Db 25


    Software
    ---------------
    Install Win Xp sp2 And Optimisation it
    Install Mach3 VR2.42
    Conect pc to Board (Pmdx-122 )
    Pic S09.jpg
    restart System

    (when System restart Relay in Board is On&Off )
    Run Driver Test And Pic S1 in Below



    Run Mach3Mill
    1- Config - select native Unit and select MM's
    2- Config -Port And Pin - Pic Below





    3- I don't know, how set Motor tuning and other config . I have a problem - Motor in not work Properly. Film in Below
    Do You Help Me .
    tank's a lot

    Mach3 , Config, Motor Tuning problem ( FILM OF MOTOR)

  2. #2
    Join Date
    Jun 2007
    Posts
    8

    Talking

    Film Of Moto Below
    Attached Files Attached Files

  3. #3
    Join Date
    May 2006
    Posts
    573
    I think your stepdrive is set way to high, as far as i can tell its set at 8000 steps per rev, try setting it to the lowest value = 400 step per rev. In mach 3 set step per unit to the same, 400 and increase acceleration to maybe 100. Now in the MDI enter G0 Y1 and the motor should spin one full turn.

    Also make sure you have set the Unit in the config menu to mm not inches

  4. #4
    Join Date
    Jun 2007
    Posts
    8
    Quote Originally Posted by Guldberg View Post
    I think your stepdrive is set way to high, as far as i can tell its set at 8000 steps per rev, try setting it to the lowest value = 400 step per rev. In mach 3 set step per unit to the same, 400 and increase acceleration to maybe 100. Now in the MDI enter G0 Y1 and the motor should spin one full turn.

    Also make sure you have set the Unit in the config menu to mm not inches
    Hello Guldberg

    But I Think On Dip

    On (down) = 0
    Off = 1

    do you think unlike

  5. #5
    Join Date
    Apr 2007
    Posts
    6
    I think On is 1 and Off is 0
    Switch 5 needs to be set off to use Step and Dir mode

  6. #6
    Join Date
    May 2006
    Posts
    573
    Maybe your right, its a bit hard to tell from the picture. I would still try and set the step per unit to the same as the step driver. And you have the mm setting correct? 4 is still way to low for acceleration.

  7. #7
    Join Date
    Jun 2007
    Posts
    8
    Hello EveryBody
    I detect Problem & crash Sound
    the wire Of A A_ b b_ is malapropos
    Then
    In config - motor tuning and setup change

    Step Per : 400
    Velocity :100
    Acc : 30
    Step Pulse : 0 What is this?
    dir Pulse : 0 What is this?

    Then Motor rotate Corectly

    -but Only rotate Left To right if is X Axis more
    not Rotate Right to Left when X is less

    Where problem ?


    in the course of Dip On Step Driver On=0 Off=1

  8. #8
    Join Date
    May 2006
    Posts
    573
    Not sure i understand correct. X axis more than what? Does it always rotate the same way no matter what you do?

Similar Threads

  1. Mach3 motor tuning question
    By kn6398 in forum Machines running Mach Software
    Replies: 10
    Last Post: 06-10-2014, 09:21 AM
  2. motor tuning problem
    By m8kingit in forum Mach Mill
    Replies: 3
    Last Post: 04-29-2009, 03:39 AM
  3. Replies: 1
    Last Post: 10-17-2007, 05:16 PM
  4. Motor tuning under Mach3
    By BAustin in forum Charter Oak Automation Support Forum
    Replies: 3
    Last Post: 12-24-2006, 06:23 AM
  5. Mach2 motor tuning problem???
    By kombayotch in forum Mach Mill
    Replies: 10
    Last Post: 03-15-2006, 09:34 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •