[gavztheouch]

I have just bought a couple of panasonic drives and motors, I think I will prob need to configure the drives to accept the right signals from Mach. For this I need Panaterm to configure the drives, does anyone have a copy they could email me?

Cheers
Gav

[gavztheouch]

Panasonic UK were helpful in emailing me the Software if anyone else is looking for Panaterm I can forward a copy to you.

Im about to power up the drives for the first time. Looking at the circuit, I need a,

1. Fuse breaker
2. Noise Filter
3. Magnetic contacter
4. AC reactor

All before I can feed my AC mains supply into the drives.

I have the noise filter, but no fuse breaker, AC reactor or Magnetic Contacter. Is it advisable to test run the drives without the other three components, will the fuse in the plug compensate for the lack of a breaker?

[daveyddd]

I would love a copy of it as I have some of these drive that we would like to use. If you could forward a copy to me I would be very greatful.

email to dave "at" myeye.ca

Thank You Very Much

[jejmule]

gavztheouch send me panaterm, thank you.
I would like to make a cable but i can't find mini-din 8p pinout.
If anyone know about this cable you're welcome.

edit one minute later
I find this document :

communication cable information

Jejmule

[gavztheouch]

Hi Dave, I've just send you a copy to that address,

Cheers
Gav

Edit: Just recieved a failure notice, do you have a limit on your account the file is over 5mb, do you have a work address?

[daveyddd]

Sorry I have been having some toruble with that email addy lately.
Can you try this one instead. dfansolato at cogeco.ca
Sorry for the trouble.
Thanks again

[MikeU]

Gav,

Any way I can get a copy of this too please?

email to gryffindor60 "at" gmail.com

Thanks.

Mike

[machine head16]

Hi Guys,

Wonder if you canb send that copy of Panaterm to me too. I have the old copy but not one that works under WinXP
Address [email protected]

[illuma]

Hi

I found this site that allows download of the software, tested and working on Vista with xp compatibility mode and installed / run with UAC turned off, RS232 via USB to serial lead and three bodged wires to insert into drive.

http://www.deltaelektronik.dk/index....d=21&Itemid=28

Regards
Mark

[machine head16]

Thanks Mark,

Tested and working perfectly.

Regards

Paul

[dreammstr6]

can anyone point me in the right direction to find the schematic for the cables needed for panaterm?

[illuma]

I have just bought a couple of panasonic drives and motors, I think I will prob need to configure the drives to accept the right signals from Mach. For this I need Panaterm to configure the drives, does anyone have a copy they could email me?

Cheers
Gav

If you send me a PM with your email address I will send you all the info you need. The drive can lock up if an error is detected and with the software and info it's quite easy to clear the stored error causing lockup.

Regards
Mark

[kmajer]

Hi,

I'm new in the cnczone, but probably somebody could help.
I have old tipe of Panasonic drives some of the MSD series and one of the MDD.
The panaterm 3.7 seems to be too new for these drives,
does sy have the old DOS version of the SW or knows how to communicate
with the old drives?
Cabeling is not a problem source.

thanks
Krisztian

[Gyros]

Guys, I downloaded panaterm but the link to the cable-info doesn't work anymore. Can anyone email me that pdf?

[Nikomas]

Gyros, which series of Panasonic do you have? MSD or MSDA?

[Gyros]

Hi Nikomas, I am not sure what you mean. I have 4 servo's Panasonic, type MHMD082P1U, with servodrivers Panasonic, type MCDDT3520052.

[Nikomas]

I not have cable-info for this series Panasonic servo motors. So sorry.

[Andrey67]

I'm using Win 7 and virtual WinXP. I downloaded Panaterm v.3.7 also. And it was installed successfully.
After selecting the type of amplifier I get the message: "Can't execute Panaterm. File is damaged. Instal the Panaterm again".
And Internal use information: File:C:\Program files\PANATERM\ini\def\MINAS-S.DEF GroupMAX ITEM Block:0 Extension:

I tried on Win2000 and had the same problem.
Why I can not run the Panaterm?

[Jimildoo]

I have the same issue - I have obtained a DV0P1960 cable from the US via eBay, but havent yet found a download for the Panaterm DV0P4460 software. Can anyone assist?

[Nikomas]

MINAS A5 family | AC Servo Motor | Product information | FA, Industrial Motor | Panasonic Industrial Solutions