Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium is cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical Data:
Mobile. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp.

Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical Data:
Mobile. With three heating elements. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 14 bar and 2.8l/min. 15 KW, 32 Amp.

Application:
Sometimes it is important during cleaning not to leave any residues, e.g. when surfaces must be absolutely free of lime (circuit boards, precision mechanics, watch industry, visible surfaces made of stainless steel), or in medical and bio-technical applications such as the production of artificial joints. For this purpose, phosphate, deionised water and acids can be used in our stainless steel units - 1000 ESE, 1000 ESR as well as 1000 ESR Tower.
Stainless steel units are also used when particularly high hygiene standards apply, e.g. in the food industry, or for particularly high purity standards, e.g. in biotechnology (artificial hips) or aerospace. Stainless steel units are also used for degreasing before powder coating or wet painting.

The working principle is based on high temperature combined with low pressure: at 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Acids can be used to clean off particularly stubborn dirt, and deionised water is used to prevent residues on surfaces.
The 1000 ESR has an attached collector with a special recycling and sedimentation system. Smaller parts weighing up to 80 kg - artificial joints, circuit boards, parts for precision mechanics, for example in the watch industry, etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.

Advantages:
- Perfectly clean surfaces without deposits, e.g. of limescale.
- Ideal for small series or individual pieces
- For particularly high hygiene requirements, e.g. in the food sector
- For particularly high cleanliness requirements, e.g. biotechnology and aerospace
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: Thanks to the 60-litre tank, it is independent of a permanent supply of cleaning medium.

Technical Data:
All parts in contact with medium are phosphate, acid- and demineralised water resistant. Media used must be compatible with stainless steel V2A (1.4301).
Mobile. With dirt water collector for parts cleaning in fibre glass with robust dripping grid (90 x 60 cm) in stainless steel. Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses fixed to chassis (no quick change couplings). Start-stop operation with pistol. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 12 bar and 2.4l/min. 9.9 KW, 16 Amp.

Application:
Specially developed for machine cleaning of machine tools with cutting oil incl. cabin, magazine, spindle, etc. Viscosity of up to 100 cSt. Without introduction of foreign medium.
The active principle is based on high temperature combined with low pressure: at up to 70 °C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles, even complex surfaces can be cleaned easily and without residues.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Cost- and time-intensive installation and removal of individual parts can be avoided
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: Thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Cleaning with your own cutting oil without the introduction of foreign substances
- Higher work safety and significantly lower costs than manual cleaning with rags
- Health friendly
- No need for chemicals at all, hence significantly reduced procurement and disposal costs
- Thus resource and environment friendly

Mobile. Without dirt water collector for parts cleaning.
5m hose with lance pistol and changeable 600mm spray lance; hose attached to chassis via quick change coupling. Start-stop operation with pistol. Stepless pressure adjustment.
Cutting oil supply without pre-pressure from 60l tank, overfill control, oil shortage disconnect, overheat fuse.
Factory-set max temperature ca. 70°C, kinematic viscosity max 100 cSt/20°C.
Capacity ca. 1.1 – 2.4l/min depending upon viscosity and pressure. 6.8 KW, 16 Amp.

Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium is cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical Data:
Mobile. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp.

Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical Data:
Mobile. With three heating elements. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 14 bar and 2.8l/min. 15 KW, 32 Amp.

Application:
Sometimes it is important during cleaning not to leave any residues, e.g. when surfaces must be absolutely free of lime (circuit boards, precision mechanics, watch industry, visible surfaces made of stainless steel), or in medical and bio-technical applications such as the production of artificial joints. For this purpose, deionised water and acids can be used in our stainless steel units - 1000 ESE, 1000 ESR as well as 1000 ESR Tower.
Stainless steel units are also used when particularly high hygiene standards apply, e.g. in the food industry, or for particularly high purity standards, e.g. in biotechnology (artificial hips) or aerospace. Stainless steel units are also used for degreasing before powder coating or wet painting.
The working principle is based on high temperature combined with low pressure: at 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Acids can be used to clean off particularly stubborn dirt, and deionised water is used to prevent residues on surfaces.
The 1000 ESR has an attached collector with a special recycling and sedimentation system. Smaller parts weighing up to 80 kg - artificial joints, circuit boards, parts for precision mechanics, for example in the watch industry, etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.

Advantages:
- Perfectly clean surfaces without deposits, e.g. of limescale.
- Ideal for small series or individual pieces
- For particularly high hygiene requirements, e.g. in the food sector
- For particularly high cleanliness requirements, e.g. biotechnology and aerospace
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: Thanks to the 60-litre tank, it is independent of a permanent supply of cleaning medium.

Technical Data:
All parts in contact with medium are acid- and demineralised water resistant. Media used must be compatible with stainless steel V2A (1.4301).
Mobile. With dirt water collector for parts cleaning in fibre glass with robust dripping grid (90 x 60 cm) in stainless steel. Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses fixed to chassis (no quick change couplings). Start-stop operation with pistol. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 12 bar and 2.4l/min. 9.9 KW, 16 Amp.

Application:
Parts cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning parts of fine and ultra-fine mechanics such as watches, jewellery and precision parts.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles, even complex surfaces, including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
The 1000 SR tower has an attached tower head with pass-throughs and a special recycling and sedimentation system. In the tower head, very small and precision parts can be cleaned and the residues, such as gold dust, can be filtered out. The used cleaning medium can be cleaned and recycled.

Advantages:
- Ideal for small and precision parts
- Ideal if raw materials such as gold dust are to be recovered
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical data:
Closed stainless steel tower cabin in V2A (1.4301) with bristle curtains, integrated lighting, heated viewing screen, exhaust fan, connection for pressurized air, and robust drip grid (90 x 60 cm).
Mobile. Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, in tower cabin 1.5m hose with spray pistol and changeable standard nozzle; hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 11.2 KW, 16 Amp.

Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools including cabin, magazine, spindle and gear room, also for retrofitting.
Ideal for cleaning large parts in combination with tub 1000 SRS.

The working principle is based on the high temperature combined with low pressure: At 95°C greasy and ölige contaminants quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces, including deep blind holes and hollow spaces, can be cleaned without any problems and without any residues.

Advantages:
• Significant time savings of idR 80-90%
• Thus reducing expensive machine downtime
• Cost and time-intensive installation and removal of individual parts can be avoided
• Mobile, ie. Can be easily transported from job site to job site
• Self-sufficient: Thanks to the 60-l tank independent of permanent supply of cleaning medium
• Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
• Höhere work safety and significantly lower costs than händische cleaning with rags
• Health-protecting
• Völlige renunciation of chemicals, thus reduced procurement and disposal costs
• Less water and waste water
• Thus resource and environmentally friendly

Technical data:
Driveable. Without tub für parts cleaning.
5m hose with lance gun and changeable 600mm spray lance, hose üconnected to the device via a quick-change coupling. Start/Stop operation über the gun. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l tank with dosing device for cleaning concentrate, ÜfÜllsicherung, water shortage shutdown, Übertemperatursicherung.
Geräteleistung approx 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp. Translated with DeepL

Application:
Handy and compact units that can be easily transported from site to site or in a station wagon, making them ideal for service providers. Without integrated tank.
Parts cleaning and machine cleaning, especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools incl. cabin, magazine, spindle etc., also for retrofitting, small and large components. Cleaning of large parts in combination with 1000 SRS collector.
The working principle is based on high temperature combined with low pressure: at 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles, even complex surfaces, including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
The 1000 SRK-AS-EA can be connected to the external water supply via a commercially available hose quick coupling as well as suck in cleaning medium from an external container with the help of a suction hose.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Cost- and time-intensive installation and removal of individual parts can be avoided
- Mobile, i.e. can be easily transported from place to place and in a station wagon
- Suction of own cooling lubricant allows cleaning with own emulsion without introduction of foreign substances
- Higher work safety and significantly lower costs than manual cleaning with rags
- Health friendly
- Largely no need for chemicals, hence significantly reduced procurement and disposal costs
- Thus resource- and environment-friendly

Mobile. Compact design without tank. For suction of liquids from separate container (AS) or directly from external water supply (EA) using pre-pressure from water pipe. Switching between suction and external water supply with 3-way valve.
5m hose with lance pistol with hand screw coupling for exchangeable lances and 600mm spray lance; hose attached to chassis via quick change coupling. Start-stop operation with pistol. Stepless pressure adjustment.
Filtration with active filter monitoring, separate ventilation cycle with de-aering pump.
Capacity ca. 7.5 bar and 1.8l/min, with pre-pressure up to ca. 12 bar and 2.4l/min, for pre-pressures from 1.5 to 6 bar. For total pressures above 8 bar reduced heating capacity. 10.1 KW, 16 Amp.

Application:
Sometimes it is important during cleaning not to leave any residues, e.g. when surfaces must be absolutely free of lime (circuit boards, precision mechanics, watch industry, visible surfaces made of stainless steel), or in medical and bio-technical applications such as the production of artificial joints. For this purpose, deionised water and acids can be used in our stainless steel units - 1000 ESE, 1000 ESR as well as 1000 ESR Tower.
Stainless steel units are also used when particularly high hygiene standards apply, e.g. in the food industry, or for particularly high purity standards, e.g. in biotechnology (artificial hips) or aerospace. Stainless steel units are also used for degreasing before powder coating or wet painting.
The working principle is based on high temperature combined with low pressure: at 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Acids can be used to clean off particularly stubborn dirt, and deionised water is used to prevent residues on surfaces.
The 1000 ESR has an attached collector with a special recycling and sedimentation system. Smaller parts weighing up to 80 kg - artificial joints, circuit boards, parts for precision mechanics, for example in the watch industry, etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.

Advantages:
- Perfectly clean surfaces without deposits, e.g. of limescale.
- Ideal for small series or individual pieces
- For particularly high hygiene requirements, e.g. in the food sector
- For particularly high cleanliness requirements, e.g. biotechnology and aerospace
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: Thanks to the 60-litre tank, it is independent of a permanent supply of cleaning medium.

Technical Data:
All parts in contact with medium are acid- and demineralised water resistant. Media used must be compatible with stainless steel V2A (1.4301).
Mobile. With dirt water collector for parts cleaning in fibre glass with robust dripping grid (90 x 60 cm) in stainless steel. Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses fixed to chassis (no quick change couplings). Start-stop operation with pistol. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 12 bar and 2.4l/min. 9.9 KW, 16 Amp.

Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium is cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical Data:
Mobile. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp.

Application:
Parts cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning parts of fine and ultra-fine mechanics such as watches, jewellery and precision parts.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles, even complex surfaces, including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
The 1000 SR tower has an attached tower head with pass-throughs and a special recycling and sedimentation system. In the tower head, very small and precision parts can be cleaned and the residues, such as gold dust, can be filtered out. The used cleaning medium can be cleaned and recycled.

Advantages:
- Ideal for small and precision parts
- Ideal if raw materials such as gold dust are to be recovered
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical data:
Closed stainless steel tower cabin in V2A (1.4301) with bristle curtains, integrated lighting, heated viewing screen, exhaust fan, connection for pressurized air, and robust drip grid (90 x 60 cm).
Mobile. Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, in tower cabin 1.5m hose with spray pistol and changeable standard nozzle; hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 11.2 KW, 16 Amp.

Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical Data:
Mobile. With three heating elements. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 14 bar and 2.8l/min. 15 KW, 32 Amp.

Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium is cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical Data:
Mobile. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp.

Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.

Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly

Technical Data:
Mobile. With three heating elements. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 14 bar and 2.8l/min. 15 KW, 32 Amp.

Application:
Machine cleaning especially for greasy, oily and complex surfaces.
Ideal for machine tools cleaning with your own cooling lubricant incl. cabin, magazine, spindle and gear room.

The SRE-EK is used for thermal desinfection especially of cooling lubricants. The lubricant from the tank of the machine tool is sucked in, thermally sterilized and returned to the machine tool. This can extend the life of the coolant and reduce the cost of the coolant and its disposal. The less frequent replacement of coolant or the disinfection in the bypass also means that the machine tools are at a standstill less often. Above all, biocides can be dispensed with, thus increasing occupational safety and reducing sick leave.
The device is mobile and can therefore be transported from machine tool to machine tool.

Advantages thermal desinfection:
• Without chemicals and without biocides
• In the bypass or. operated during running production, therefore no machine downtimes
• Longer service life of the cooling lubricant = considerable savings for purchase and disposal of the cooling lubricant
• Higher occupational safety = lower sickness rates since no chemicals and no biocide
• Mobile, i.e. Can be easily transported from machine tool to machine tool

Advantages cleaning:
• Significant time savings of idR 80-90%
• Self-sufficient: Thanks to the 60-l tank independent of permanent supply of cleaning medium
• Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
• Significantly lower costs than manual cleaning with rags

The operating principle is based on the high temperature combined with low pressure: At 95°C, greasy and oily soils dissolve quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces up to deep sack holes and cavities can be cleaned without any problems and without any rests .

Technical data:
Drivable. Without collector for parts cleaning. With three heating elements.
5m hose with lance gun and changeable 600mm spray lance, hose connected to the device via a quick-change coupling. Start/stop operation üvia the gun. Stepless pressure adjustment.
Water and medium supply without pre-pressure from 60l tank, 5l tank with dosing device for cleaning concentrate, water shortage shutdown, temperature control.
Capacity desinfection : 6l/min.  Capacity cleaning :1,8l/min.   7,5bar 10 KW, 16 Amp.

Application:
Machine cleaning especially for greasy, oily and complex surfaces.
Ideal for cleaning machine tools with their own cooling lubricant incl. cabin, magazine, spindle and gear room.

The SRE-EK is used for thermal sterilization especially of cooling lubricants. The coolant from the tank of the machine tool is sucked in, thermally sterilized and returned to the machine tool. This can extend the life of the coolant and reduce the cost of the coolant and its disposal. The less frequent replacement of coolant or the disinfection in the bypass also means that the machine tools are at a standstill less often. Above all, biocides can be dispensed with, thus increasing occupational safety and reducing sick leave.
The device is mobile and can therefore be transported from machine tool to machine tool.

Advantages of sterilization:
• Without chemicals and without biocides
• Operated in bypass or operated during ongoing production, therefore no machine downtime
• Longer service life of the cooling lubricant = considerable savings for purchase and disposal of the coolant
• Higher occupational safety = lower sickness rates since no chemicals and no biocides
• Mobile, i.e.h. Can be easily transported from machine tool to machine tool

Advantages cleaning:
• Significant time savings of idR 80-90%
• Self-sufficient: Thanks to the 60-l tank independent of permanent supply of cleaning medium
• Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
• Significantly lower costs than manual cleaning with rags

The operating principle is based on the high temperature combined with low pressure: At 95°C, greasy and öly soils dissolve quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces up to deep sack holes and cavities can be cleaned without any problems and without any rests.

Technical data:
Drivable. Without collector for parts cleaning. With three heating elements.
5m hose with lance gun and replaceable 600mm spray lance, hose üconnected to the device via a quick-change coupling. Start/stop operation üvia the gun. Stepless pressure adjustment.
Water and medium supply without pre-pressure from 60l tank, 5l tank with dosing device for cleaning concentrate, water shortage shutdown, Temperature control.
Capacity desinfection: 6l/min.  Cleaning:1.8l/min. 7,5bar .10 KW, 16 Amp.

Application:
The Thermo-EK is used for the thermal disinfection of cooling lubricants. The coolant from the machine tool tank is sucked in, thermally sterilized and returned to the machine tool. This can extend the service life of the coolant and reduce the cost of the coolant and its removal. The less frequent replacement of coolant and the disinfection in the bypass also reduces the downtime of the molds. Above all, biocides can be dispensed with, thus increasing work safety and reducing sickness.
The equipment is mobile and can therefore be transferred from tool to tool.

Advantages:
• Without chemicals and without biocides
• In bypass or. operated during ongoing production, therefore no machine downtime
• Längere life of the cooling lubricant = considerable savings für purchase and disposal of the KSS
• Höhere occupational safety = lower Krankenstände since without chemistry and without biocide
• Mobile, ie.i.e. can be easily transported from machine tool to machine tool

Technical data:
Mobile, in compact design, without tank. Allows suction and thermal sterilization of liquids from separate tank. Filtration with active filter monitoring, adjustable monitoring of the bath temperature on the suction side, 5m suction and return hoses.
Equipment output approx. 5l/min, 5 KW, consumption approx. 4 KW due to heat recovery.
Weight : 55 kg