Hello
I think here is many elctronic hobbyist too.
I need to try make tssop16DIP16 adapters. If you have Eagle or some other PCB software, please help. And better if you can convert it to .ecp...
Type: Posts; User: salmve
Hello
I think here is many elctronic hobbyist too.
I need to try make tssop16DIP16 adapters. If you have Eagle or some other PCB software, please help. And better if you can convert it to .ecp...
Hello
What material and thickness you can cut with 1000W Co2 laser machine?
How about 3M??
PM sent
Vekku
0MC limits programnumbers to 200. There is still free memory space. How to get more.
Machine is DahLih MCV1020.
Thanks
Vekku
Just curiously I opened the controlbox.
What are these three red leds?:
https://picasaweb.google.com/salmve/HaasIndexer?authkey=Gv1sRgCO3t_uz-o6qCCw#5602427165679840786
They lit all the time
...
Ok
Now i have tested it many ways and it looks like RS232 interface is someway broken.
Tried to send program out from HRT. Empty connector, only scope connected.
CH1= pin3 and CH2=pin2
...
So, probe between 3 and 7, others NC??
Thanks
If i use oscilloscope only (no PC at all) to see what happens, what pins i have to connect. Probe between 2 and 7 (transmit data, signal ground) How others?
Vekku
Thanks. Lets try. I have oscilloscope connected to DB25 pin2. I wrote little program into Haas and tried to get it out. No success. Haas display is blinking SEnding, but nothing to see in scope...
Hello
I am trying to control HRT-210 indexer with control box via serial port. I want to use indexer independet, without CNC-machine. I am using program named Terminal, downloaded from here:...
Hello rolandkra and others.
Happy New Year!
Have you read this thread?
http://www.cnczone.com/forums/fanuc/78478-problem_6m_spindle_drive.html
I havent got solution to the problem but with...
I dont think so. Here is picture with better resolution.
Picasa Web Albums - Vekku - Vinyl cutter
Pattern is draw by cutter test program. I think its very good, isn't it?
Vekku
No succes! Machine (cutter) shows: Now is cutting....
but nothing happens. I have to push Reset to get it wake up again.
Vekku
Thanks. I will try this.
Vekku
Hello
I have just bought cheap chinese vinyl cutter. Few hours of try i got it work.
I have used pen at first attempts.
Please, glance results:
Picasa Web Albums - Vekku - Vinyl cutter
...
Little old thread but still....
Where i can find paint mask i can cut with laser. Local supplier has paint mask but it is PVC and it's not good to machine and operator.
Thanks
Vekku
See this page:
http://www.scottware.net/Lasers/NarrowMove.html
There has no dimensions but maybe it helps.
Vekku
Thanks for both of you.
As i said i am just starting my laserhobby. So the materials and methods are not clear yet. Time will show.
Two offers are uppermost, so i have to decide which one. Both...
Thanks for the intrest.
Let us suppose that we use same machine and engrave same job with 100w tube and after that 60w tube. Previous test we have found out that required power is 30w. 100w tube...
Hello all
I am asking offers from few Chinese laser manufacturers direct from China.
I have got each other better offers, and assurances of good quality:).
That is ok and relevant.
But...
Thank you very much for offer of help, but problem has already solved.
I purchased whole new set of eproms from Injunear. Thanks.
Machine is now working condition.:wave:
Vekku
Hello
Pleasant to hear that with my tips you find something from your machine.
Sounds same problem. Just that area i warmed up.
Next time when you start the cold machine, try with very slow...
BigDamo, have you regognize any difference at motor voice when the fault is on?
I think i have a same problem. When i start the cold machine and turn spindle on, it starts normally but motor voice...
Does this help?
http://picasaweb.google.com/salmve/Nakamura#
Vekku
Hello
It works!
http://www.cnczone.com/forums/showthread.php?t=63022
Reason was seven faulty eproms.
Is there any way (parameter) to change "screen order"? If i hit POS key, i get U and W...
Sorry for delay. I have been busy and away from net.
Injunear, do you really have right program!
I need series 992 version 07 eprom numbers:
001G
002G
011F
022F
041F
111F
Mark
Thank you for offer of help, but this problem has already solved. Bubble memory has initialise and other board attached to masterboard has tested ok.
Main problem was 7 faulty eproms at the...
Dan
Sorry if i will be harping on the same string. But still.
quote
"The earlier versions had the limited IL mode that you describe, and the repair of the bubble board is not possible by manual...
What a shame. I thought this is model B.
I cannot even found that ILD pin. Could it be named for another way?
Maybe i have to make some inquery to find 6TB machine. Hard to believe i will find...