Well the boxes look good but have you opened them and checked the consumables? They used to etch all of their parts years ago but Im not sure if they still do this. Did you order them from a...
Type: Posts; User: Web Goblin
Well the boxes look good but have you opened them and checked the consumables? They used to etch all of their parts years ago but Im not sure if they still do this. Did you order them from a...
Jim,
tested this out tonight on my bench power supply and it works perfectly.
Many thanks for your help.
Ian
Jim,
thanks very much for testing this out. I will give it a go at the weekend.
That's great Jim thanks.
Guys thanks for all the replies.
I would like to see if this can be done with hardware alone.
Jim did you manage to get the mpg to control the stepper driver?
Hi all.
I have been searching for an answer to something and hopefully someone here can point me in the right direction. I am looking to make and fit a power raise/lower to my warco gh universal...
For machine manufacturers in the UK you could also look at Messer and Esab.
Hi all,
would anyone have a schematic for a Kinco 2m2280n driver?
Hi all.
I have some of the 2M2280N stepper drivers which I am going to connect up to my new CSlabs CSMIO/IP-S controller.
I was wondering if anyone else has used this combination and how did you...
Since you are plasma cutting you will not get sharp corners, especially on an "inside" one. "Outside" corners can be improved to be reasonable by doing a loop so that the plasma cut crosses over...
We have a 3KW co2 at work and I certainly would not trust my eyeballs to lab glasses.
You need the correct protection for the laser.
We have safety glasses provided by a company called laser...
Buy a legal version of the software.
You can get them here( Male Metric Thread - Brass Hosetail ) but its in the UK.
The code is indeed essi. Very common in plasma, oxyfuel or laser cutting machines.
Angelo, did you get your machine from Esab? If so then they should have supplied you with an essi programming...
Rob,
the pendant looks good. The only question I have is about the speed multiplier. The manual shows steps from 0.1 to 100 but yours is labelled different. Will it give the same results?
I have used a safety relay in my panel but I need to do a bit more wiring to get it working the way I want it. I also need to figure out how to get the 10HZ pulse output from the watchdog into the...
I would say that your travelling too fast. With a standard plasma cutter you aren't going to get vertical edges. To get proper vertical cuts you need hidef or even better a rotation unit with zero...
I haven't done a build log at all with this machine but Ill post a couple of photos here just to show roughly where my new machine is at. I am hoping to get power on it this weekend to check a few...
Fusion 360 is free if you are a startup or hobbyist. I think the limit is 100K a year turnover or less.
Hi,
sorry to hear that youve been done from Marchant Dice. I dealt with them a few years ago and had problems getting my money back off of them as well after they sent me old parts claiming them to...
A programming app for edingcnc? Now thats something I would like to see. It should make it easier for us non-programmers to get our heads round.
This would work but you would have to get the correct units. We did it a long time ago with hypertherm units. I think it was the 400 or 401 power supplies. They were doubled up to give 750 amps...
Rob,
any updates on the machine? I was running eding cnc for a while on a cpu4 card but I scrapped the machine at the start of this year to build a better one but its not finished yet. I am moving...
The most used parts will be electrode and nozzle probably.
How long they last depends on a few things, piercing and cutting height being correct. Gas pressure being correct and clean. Also doing...
That really depends on the size of the plate and the actual meterage of the cut. To cut 15mm I think you would need to run it at 65amps which has a duty cycle of around 50% I think so i would doubt...
Thanks Arie. I have found the icons and which ones I need to change. I think I have the ideal icons for what I want as well so now need to draw them up and try them out.
I tried this last night in simulation mode away from the machine and it worked perfectly. Thanks very much for all your help guys. Now I just need to sort out changing the user icons for something...
I put the z axis last because I wanted to move the x and y axis to the stored point first then bring the z axis down to the stored point for it. As I said before I don't have any programming...
Arie,
Thanks for the help.
I take it that 5001 is x axis, 5002 is y axis and 5003 is z axis. Can I just add the axis I need or do I have to add all of them to the user macro?
Would this work to...
That would be great thanks.