Search:

Hi all
Any person have this machine ? i need parameter
Fanuc OM

my old monitor( RGB BNC socket , i think this protocol is "Sync On Green" ) dead and now i find vga socket in controller.
i see this message in manual :
This interface is to be used for service...

i have similar this error in osp7000:

1-1 cpu-alarm bus error (system bus)
bus error status (SBER,SBPAR,CYO,O,PRT,DIA,LOP,ECC)=80
SSW=0145 ACCESS ADDRESS=DE000000

anybody can help me?

anybody could remove this error ?
At this time,i have this error in Opus5000 ,but i dont know which one :
TCC or turret encoder

you should connect motor to servo driver.
i think you dont have any problem in driver.
Amir

i used standard pocketing.
is it possible more explain?
I'm confused.

Exactly what I need
nobody guide me?

i am newbie in mastercam.i design a cad model in solidwork and save it with parasolid format. i import it to mastercam .
now i want pocketing surface (image 1).
when i select surface (yellow...

pin 1&2 : power for motor(~ +24V)
pin 3&4&6 : GND
pin 5 :VCC (= +5V)
pin 7 :CW
pin 8 :CCW
pin 11: power down
pin 12 : Enable

Amir

Nobody ?

i have Yaskawa servo drive with serial : cacr sr 15 bc
yaskawa PDF
in this manual , i see input voltage is three phase 200~230V
is it possible i run this driver with single phase 200 vlot ?
any...

no body, any opinion

thx bob for link. the first link Was almost irrelevant to the welding ,Was more Epoxy.Anyway thx

hey guys ,i have a idea about machining bed rail.
I accidentally found a link about portable...

thx for share your experiment.
yes, over heating is important for tolerance.
also if we use many bead Around the workpiece.
but i dont have much experience about welding.
my question is about...

this is strange for me.
i think when we welding a part , it will transform.
How does it without Tolerance?

Amir

your meaning from other ways is SHIM ?

in addition I can not find any link or DIY machine with shim method.

Whether this method(shim) is accurate enough for big router?
I did research about prices for machining with gantry milling :about 2000$

Again
I have an unanswered question : about welding and machining
How these dimension of machining is done?
AND Do machining is required ?

thx Lee for Decisive reply.
The example you have stated is absolutely correct but i see "Techno Router" and was doubt because they used ballscrew in the center of the axis for long axis. and i think...

Two of our friends had suggested that starter this thread To review about "mechmate machine".
but i think The two are at different design And does not help.

Ever seen like it

yes ,but i compare this two design in terms of solidity.
i think center frame is stability because the gantry are connected from The two side.

Amir

Was very useful
But why unfinished?
Almost all the friends was agree with this theory "A 10' long acme lead screw is foolish"
Should we use the R&P for long X axis?
but i find many machine that...

i need about 10A peak current. i have IRL640(logic gate) and i want test it.
VDSS=200V & Id=17A and RDS(on)=0.18ohm

i see YAPSCV1 webpage ,MAX wrote 100A peak but I do not think is achievable
...

i used capacitor(104) between A+,B+ and I+ & GND .
now when i dont have any pulse ,shaft is motionless.

in addition,i used DC motor(180V) for my spindle.
i have a question, can i use power stage...

i solved my problem.
noise in encoder.
thx Iron-Man for guide and support.

Amir

thx for try.
Today, i do a test . link Pin analog together(short circuit) then analog input equal 0V.then i set Pin S-ON , result :dont movement
i guess my drive dont have problem , I am...

I get close to the destination:D
in fact, brand my servo is Panasonic but made by Yaskawa.(i think)
i dont can find any manual for it in google search.
i dont know how should adjust potantiometers...

Exactly,
i use Yaskawa servo drive(Speed control). my driver is old
in addition, i dont have any information about SPD/Kp & KV & PI potansiometer

Amir

thx for reply
please see my video.
YAPSC
Amir