I forgot to say that is possible to send and receive programs via RS232 in Edit mode.
Also I have a partner that has available the Fanuc FAPT software to compile the new ladder.
Type: Posts; User: the_catalyst
I forgot to say that is possible to send and receive programs via RS232 in Edit mode.
Also I have a partner that has available the Fanuc FAPT software to compile the new ladder.
I have found a device, you can find on eBay as TL866II USB Programmer for eprom
Hey there,
We have a Leblond Makino RMC-55 1991, the machine is in excellent shape. I chose this machine to make mold repairs and some fittings in finished parts. I couldn´t check the machine...
Send me pm with your email
Enviado desde mi Redmi Note 3 mediante Tapatalk
i justo bought a rmc from 1991. I hace the manuals, send me pm with tour email
Enviado desde mi Redmi Note 3 mediante Tapatalk
It turned out to be right threaded Bolt, but It was stuck with a lot of loctite. We had to use a 3/4" x 20" handle to loose It.
After this everything went smooth, as usual.
Enviado desde mi...
Hello,
We've been asigned to change the coil springs in this horizontal machining center. As usual we started taking out the cylinder to pull out the draw bar assembly but It does not go through...
Hello Chandru,
Did you figure out how to solve this situation? Our Mori, a SL-25 with MF-T6 control is giving us such headache and we haven´t find the origin of the alarm.
Any sugestion will...
Hello,
I'm stuck with this project. We have to machine a wormscrew and it was thought to be made in the haas with 4th axis. Then we face our problem, the Bobcam license own by the workshop is...
Thanks Freaky ,
Nowadays I'm not able to be in factory, let me see next week what I can check. I don´t remember any custom PMC, but I´m not sure right now.
The Monday.com sugested by CNCWayToGo is being advertised a lot lately, but I haven´t start the trial to make a revies. Instead I have used MS Project and is the one I´m attached to, the Gantt...
Hello,
I´ve been assigned to get back to operation a Robodrill. The machine was in production line for a specific operation, due to this it had some fixtures and sensors to ensure the proper...
Hola:
Ofrezco el servicio de programación de centro de maquinado 3 ejes, tenemos una licencia de Hypermill 2020. Por si alguien ocupa escribanme mensaje directo con su correo para ponernos de...
What bolt are you refering to?
Enviado desde mi SM-J700M mediante Tapatalk
As mbservice says for dripfeed:
?Tape mode
?Cycle start (in my control lsk starts blinking on the screen)
?Send from the PC
Maybe this doesn't work. In that case try only transfer the...
Yeah, we are running G01 with M130 and the spindle as usual. M131 is active even with the spindle running.
It seems that the needing to command M130 is a damaged interlock in the ATC door, but I'm...
Yeah. It could be obvious, but sometimes is oka go to the basics. We tried with spindle on and off, no movement with G01 was allowed.
Later I found in the operation manual the M130 condition to...
Hello Kitten,
The handwheel works, but the jog buttons doesn’t make movements.
The control admits and executes incremental commands. The commanded block moves all the axis +10.0
In any...
Oh partners, there´s a new situation. We have set the home position, now we´re running the first program test. Everything ok until a linear interpolation is commanded with G1, no matter what axis,...
Hello Wiz,
You were right, there´s no just a number, it could be a variety depending on the current postion of the encoder, so if somebody is found in such situation they will have to start...
Hello Kitten
Once the encoders were rotated the new position was updated and the limits seems to be the same as before. We have checked the parameters, beside the ones we changed, they are still...
Wiz,
Thank you for the advice. Well there are times it turns out to be such a hunt. Mine starts tomorrow.
I see in the parameters screen N TRAVEL LIMIT and P TRAVEL LIMIT must have the same...
Hello,
In newbie to Okumas, and here we have a VMC MB-46VA equipped with OSP-E100L control that has lost home. The initial position was showing big numbers in the three axis, the Z axis was...
Just as Ian said, use a boring head to ensure cylindricity. If is a single part or a small batch I´d rather use a holtest micrometer to measure the bore.
Greeting
Ari
Hello Johnsmitty,
I would send the part to heat treatment without the helicoil inserts and add them after the temper. But I haven´t had a piece in such situation, this would be my approach.
...
Hello Dcoupar,
Send me pivate message with your email address, I will send the manual to you.
Ari
Hello partners,
I'm setting a RS232 connection from PC to a vmc equipped with Fanuc 11M. All the parameters have been set according to the Fanuc RS232 connection manual. The machine is a vmc...
Hello ddkor, very impressive build, congratulations.
Could you upload the design to check it out as reference, please.
Have you tried cutting aluminum?
Stay cool ;)
Hello,
We just bought a Blohm Simplex 7 (1965), 12"x24" surface grinder, but it came with no manuals. Nowadays we are making a deep maintainance to get this machine tuned. I wonder if some of you...
Hi Jacof, Zavateabdu,
After a long time we have figured it out. It was only the lenght between the sensor and the lever mounted on the spindle. The sensor has always sent signal, showing...