Search:

Sorry for the delay in replying , i dont monitor cnc zone regularly ,
without knowing the chipset of the USB wifi adapter your using , i'll guess that it is a realtek chipset , and that although...

Make sure that your fusion post is outputting the correct M code M7,M8 etc, you can issue an mdi command to test the M code works.
I,ll guess that perhaps fusion is not giving the correct mcode

It can be done directly, using a spare pin on the 5i25, I would not recommend USB, but it could be done,depends if the time to do it is worth it.

Not sure what your requirements are, it,s simple enough

Sarah

Depends on what you wish to do, however I doubt it as pathpilot is based on Linuxcnc see Linuxcnc.org

Pathpilot is based on Linuxcnc,so yes search macros on Linuxcnc.org

LOOK UP G18 or G19 , i forgot which and i'm out for the day

Sarah

attached

the xhc-04 wireless pendant will work ,but not out the box , although you will need to modify the config files and add a few files from a previous version of linuxcnc ,

i dont see why the...

don't know what you mean by Jailbreak ! , theirs nothing to break ! . it's not windows you know ! ,
pathpilot installs linux ubuntu 10_04 as it's os .

if you mean you want to use it for non...

i'll pm you my email , if can send me the offending file , i'll take a look

just modify your post processor and remove the M3 then save as a different post ,
S0 is not a stop spindle command this only means zero speed , M3 is start & M5 is stop

their are many...

what post processor are you selecting / using ? , make sure the gcode ends in .ngc

i'm guessing , it just got it's knickers in a twist , with trying to execute more than one command in the buffer , whilst execuiting another .
this can happen if your using the handwheels for...

i have a forum area setup for Pathpilot on linuxcnc.org .
i tend to spend most of my time there . anything your stuck on take a look there perhaps .

and it all depends if you have been used to...

@mooser

ok i'll see what I can find out from vistacnc , I have the code details for some of the models , which i'm looking at the moment
i'll ask if it's the same code base as I already have ,...

send me some details of the pendant , and i'll see what can be done .

Thanks ,
hopefully we can get to the bottom of this shortly

Jim ,
Sorry guys , work got in the way ...
Jim can you give me any errors you have or what hiccups your getting , so we can solve this , I don't have a pendant to test , but that shouldn't stop...

i have located the problem with the vc-2ps file , this is also kernel specific so using the files from vistacnc will in some cases produce errors
i'll post a replacement for pathpilot here shortly...

@Andyf97 ,
you can access a windows network to access gcode files etc from a shared network
http://www.tormach.com/uploads/898/TD10345_Networking_PathPilot_0415A-pdf.html

Pathpilot is linuxcnc,so they should be no difference, if you care to send me direct your config files incl the pendant, changes, I,ll put it right.

Pathpilot is a bit dumb,it only needs to spit...

for the vista p2s ( or p4s) you'll need to re-flash the pendant , and add a configuration to your pathpilot hal files
if you confident in configuration of Linuxcnc ? , the files are available from...

which pendant do you need ? , i'm currently adding a few into my version of pathpilot . mainly the xhc-04

i'll guess this is related to the USB interface used for the coolant , and will just be related to how fast the USB stack is cleared , overall it should not have any effect other than just being...

Theirs no good reason for any probe , not to work , with mastercam .
it will only be a change of the postprocessor for any probe to work , there not rocket science.

unfortunately not , you need to add the updates manually and fix any unforeseen problems, and in some cases that may not even be possible ,
i'm hoping to be able to do that shortly , but it will...

PathPilot was origionaly started when Linuxcnc was using 10.04 ,( around linuxcnc version 2.6.3) and due to some constraints and stability kept to it .
updating to a new current kernel etc ,...

as far as i am aware , their is no option to select an optional configuration , however , adding the config to the tmc/config folder & then changing the config_file.txt to suit
will allow you to...

send me details of the camera , and i'll see about interfacing it , but may be a few days or so
pm me