Shoot me a direct email [email protected]. For some reading I can’t get the PMs to work
Type: Posts; User: zpsbob
Shoot me a direct email [email protected]. For some reading I can’t get the PMs to work
Start here:
http://www.kiraamerica.com/companyinfoamerica.php
I'm not 100% sure, but I think that is a drain tube for oil in the headstock
Sweet! glad you got it going. Be careful with those Vogel lube pumps. They are very expensive!
[email protected]
There should be a filter in line after the lube pump and a filter screen on the oil intake inside the oil tank itself.
There are two versions of the Vogel lube system used on these machines. One...
From the ladder: MTB FAULT MESSAGE 20: 20 LUBRICATION TIMEOUT
The machine is not satisfying (closing) the lubrication pressure switches within the allotted time, or if they are closing they are...
Oh… also… clean the chips out of the two grey troughs with covers on the back of the machine.
There should be a key switch for “deblock limit switch” I think on the side of the electrical cabinet. Turn the switch, press data reset, then press start. You should be able to jog off switch. Some...
Tree sold the head as a separate assembly and they got glued to just about any type of machine you can imagine. They marketed it as the MH-4 head and it probably got stuck to the Italian iron...
Ideally, if you can get your hands on a scope that's the best way to check the encoder signal. Check the plug inside the electrical box on the spindle motor (power off of course) to verify it is...
The -pg error is pulse generator. It is missing some component of the spindle motor encoder signal. The blown fuse can happen for too many max power surges because of the lost encoder signal (it will...
Good luck. Shoot me an email if you need anything else!
[email protected]
Look up in the taper. Rev 3 has collet with 6 balls and 6mm Allen screw in middle. Rev 2 has a collet with 3 balls and a knock-out button in center past the taper. Rev 1 has 6 pins, 3 each on two...
Have you gotten this straightened out?
Sorry, late to the party.
No westamp drives were ever put on J425 machines.
Balance the lag on the 2100 machines:
Press DISPLAY
Select SERVO SETUP, Press the green check mark
Select a linear...
Give me a call in the office, 262-758-6129. Ask for bob
What model machine?
original configuration was rotary windup
Looks like Monica quoted you the bearings already. Be advised: There are 3 completely different bearing sets in 5 different configurations.
Yup.. welcome to my life. LOL. I actually wrote that procedure specifically for a customer who bought a used 800 from me. The operator just refused to do it per instructions, so I had to make it very...
Another way of doing it:
Tool and Fixture offset setting on A2100
Required: gauge block for setting tools. 1-2-3 block or similar. Always use same side
Tool length setting:
1. MDI tool into...
Here's a strange request... I had a customer call me a few months ago looking for an Erickson QuickChange 30 spindle for a TREE 2UVR. I scoured high and low but couldn't find anything about it, much...
It will do the trick for a little while, but will smoke the drive from overloading
So this gets archived:
To make the control on a J325 / J425 go from 3500 rpm to 6000, add a jumper from 24vdc in machine to wire/terminal 238. Most machine the 24vdc can be sourced at the adjacent...
All of us at ZPS-CNC USA handle the support and have since ZPS stopped supplying the machines to TREE. We have done everything we can to make the path for information and support simple, we even...
that's will fit some of the vmc's not the 325. Let me check...
Similar from VXB is $423/ea (unmatched). Grainger 836.50/pr. ZPS 552/pr.
Which parts are you after? We still have quite a few and if they're "old stock" they're usually bargain priced
[email protected]
Glad its going!!
Bob
Absolutely. What is on the Y and Z motors? Did someone move them around?
What motors are on the axes? Baldor taper shaft? MSI? Baldor straight shaft? They take different pulleys
Bob