Search:

Ok, so I updated a simple hole drilling program we've used for a while on various machines, and added some functionality.
I've gone over it a few times and ran some parts using it, but I am curious...

Hey D, I see you helped out on the Daewoo again :) Appreciate the help (El is one of our maint guys).
Not sure if you talked to him on the phone or not, but I wanted to update any thread followers...

Anticlockwise? Makes clockwise seem like a bad thing!

Chris is right, to add to that, the line you are looking for would be something like G02 X-2.5 Y2.5 R2.5 F40.0 (assuming that this block is...

Well, what I would do in this situation is have the same start and end points for your arc, and just slowly decrease the radius. As you decrease the radius, the slot will get deeper at the center....

Hey guys, not sure how useful this is for all of you, but it has been a huge help for us here. I have a mill bore program, written as a sub, that will mill a hole of any diameter and depth with any...

I'd be happy to help out as well if it's not too late. If you need anything send me a PM and I'll get back at you.

Ok guys (for those following or anyone that stumbles upon this in the future).
The problem lied with the roller switches that tell the tool clamp/unclamp status. The bottom roller switch was stuck,...

Ok, sorry, I wasn't able to connect to the forums for quite a while there.
I went to take a video, and then I realized that there is really only 2 screens. Here's the shots from both of them (doubt...

Well, found the info on our 15i on a laser, however (and I should've specified earlier), on the 0M-C on the Daewoo the system hard key doesn't exist. I looked everywhere I could think to look, but I...

Well, I did some digging, and some searching, and have no idea how to find the ladder version. Any hints? :D

First, the issue. When a tool change is called in a program, the tool gripper closes and the tool unclamps like it should, but then it pauses for a few seconds and alarms out with "No.2055 ATC Z-axis...

Bit of a late reply, sorry
I currently run 2 87' Mycenter 2's, and had previously run a 3X-APC. The only problems we ever had with the 3 were relating to the pallet changer, and that was due to a...

Yeah, alarm pops up in a fresh program any time you get to the point where youre selecting sub options (ie: it will let you select hole, but not drill).
It's not really a necessity, just one of...

No, definitely CAPS. Here's some pics.

http://i.imgur.com/piSEt.jpg
http://i.imgur.com/2NgXp.jpg

Thought FAPT was a turning convo setup?

Hey guys,
So i was playing around with things on our 11M controller (Kitamura Mycenter 2B), and i went to open up the CAP programming after doing a little reading online.
All went well up...

chat,
Unfortunately, that won't punch out your ladder programming from the plc, only variables, programs, and parameters.

Vezku,
You just saved our butts as well, Just had an 87' Myventer 2B go down with the exact issues you had, and our maint guy found this thread. Just had to hop on and give you a thanks!

At our shop we use NCNet (the free version), which only supports 1 machine setup, but through the use of a transfer switch we have it wired out to all 3 machines. According to their website (DNC –...

thread is here: fanuc ot-c parts counter,

"Parameters:
0040.3: count (0) or not count (1) total number of parts M2/ M30 executed.
219: When preset Mcode is executed total parts is counted....

Indirectly, yes :)
Tried M54 and nothing happened, so i started digging on M code parts count, and came across a parameter that you set to make a M code add to the part counter (sorry, its late,...

We've recently aquired a Daewoo ACE V-35 with a 0-MC controller and rotary pallet changer, and I'm having a problem getting a cycle counter working.
On the other machines (no pallet changer), you...

this thread is almost 5 years old. that engine is prolly blown by now :)

Doesn't look like there's much logic behind it, at least from our perspective. An interesting read though: FANUC - Wikipedia, the free encyclopedia

I've got a 3 block look ahead on both of the 11M's i run regularly, not saying it isnt a possibility though.

On the program check screen, does it show you a programmed vs. actual feedrate? If it is changing the actual and the programmed rate remains the same, I'd take a look at the feedrate override switch...

If my math is correct, and sometimes i get lucky, at 9600 baud you should be hitting 1.2Kb/s, at roubdabouts 50s for your 60Kb file.
I run 1200baud and 3Kb files take only a few seconds. (Long...

alright, so i tried a .25R lead in after a .10 X move, but i was using a thinner piece of scrap, and viola, no marks! We'll see how well this holds up on the thicker stuff, but I'd like to believe...

Still a mystery on the hole location. On one of our machines we programmed all milling to G58/59, and the hole only to G56/57. After setting the locations EXACTLY the same, the hole was exactly where...

Oh come on guys, i couldn't blow you off :)
Just having difficulties with a lot of things, not this part related. I came in sunday night to find that suddenly these parts that were hot as hell were...

Anything that is said helps in some manner or form...
So, are you saying that the besy way to lead in and out of the rad is with at least tool dia (that is actually spelled out in the manual), and...