Search:

Hellow Reyad!
I have Fanuc 6T model B maintenance Manual in Japanese.
If you want this, Send me your E-mail add. please.
My E-mail : [email protected]

Regards!

Regards!

Hellow Daniel,
Have you got soft(994 ver 25 or later)?
If you didn't yet, I can get it in Korea.

Best regards!

Daecheol Sung

Dear VENKATESH,

600 PC ALARM is Data transfer error from MDI & Connection unit.
Please Refer attached files.

Best regards!

Daecheol Sung

Dear Lene,
Could you tell me result of try as follows(Delete or skip M,S,T code and insert M30 at the end of Main program).
(M6 T1);
(G00 X0 Y0 Z0,5 S400 M13);
.
.
.
G65 H01 P#132 Q25000
M98...

Hi Greg,

I have

63004E
63005E
63010E
63014E

Send me your E-mail address to [email protected]

Hi CNCZILLA,
Thank you for your kindly reply.
It will be of much benefit to me.
Please send me pdf. file to [email protected]
Thank you again!

Hi Nick,
I need Maintenance manual and Electric circuit drawings for OSP-3000 on MC-6V.
Help me please!

Hi Sami,
I have FANUC 6T-B manual in Japanish.
I have FANUC 6M-B manual in English.
DGN maps are some deference. Witch do you prefer?

Hi Paresh,

You can adjust by potentiometer on servo amplifier.
Refer attached file please.

Good luck!

Hi Sami,
700 == 00010000 means Feed ovrride is at 0%.
Please check DGN 103.0~103.5 for Feed override signals.
Good luck!

Can you send me LIST of DGN 700,701 and 712?

Hi Sami,
Can you check by diagnosis signals?
Refer attached file.
Good luck!

Isn't there any interlock ?
Who made your lathe?
Do you have electric circuit drawings and PLC ladder diagram?

Hi,
Could you send me electric circuit drawings and PLC ladder diagram?
You can command INC movement by U654.321 and W123.456,
and ABS movement is X123.456 and Z654.321.
Good luck!

Hi Sami,

It's working normally.
There's no display of multi block contents in 6T-A CNC.
Just same with 2nd attached screen.

Good luck!

Hi,
Do you have Electric circuit drawings and PLC ladder diagram?
Who made the lathe?
And could you send me Parameter list NO.0~No.4?

No, you can't set this bit by G-code.
You can set by switch operatoin.

Hi Snowie,

You have to set "1" DGN 104.1(ABS) by "Manual absolute"switch ON.
You can confirm at diagnosis screen.

DIAGNOSIS
NO
104 * * * * * * 1 *

Good luck!

Hellow Parker,
Incorrect parameters would prevent the spindle operating.
Do you have electric circuit drawings?
Could you send me the drawings if you have?
Best regards!

Hi Parker,
Did you try change the poles of power supply lines?
Maybe your machine was installed with SCR servo drive unit.
Then you must set phase angle of Power line,or not servo dances.
Good...

[QUOTE=Sung daecheol;745747]Here's location of switch.
It's middle of the picture
← →
PRM NOR

I'm sorry I don't know to edit picture.
and I don't know how to attatch files.
I'll...

Here's location of switch.
It's middle of the picture ← →
PRM NOR

I'm sorry I don't know to edit picture.

Best regards.

Hi Parker,
I dealt 5T 25years ago.
I think Write enable switch is rear of DPL panel, but i can't assure.

Hi Parker,
I sent parameter list to your mail.
I've sent another mail before.
But It's more Helpful Ahn's Parameter(attached file) than mine.
Good luck!

Didn't you receive my attached file?

I'll send you again to your mail.

Unfortunately, I don't have any parameter manual for control.

If you locate parameter for me, that will be so helpful to me.

I sincerely thank you for your kindness.

I will wait for your...

Thank you Stevo,

I cleared sum check error.
But I have a small problem that Screen disply Japanese.
I think display language controls by PARAMETER.
Do you know Witch bit is English display?
or...

Hi Rony!

It(DNG700.3) means "Not reached INPOSION BAND of setting amount(PRM No.70(X) 71(Y) 72(Z))".
You can see POSITION DEVIATION in DGN No. 800(X), 801(Y), 802(Z)

You can resolve by 2...