It is considerably faster to draw in Ironcad as opposed to any thing I've ever used and that includes Solidworks. Threading is faster, there is a gear module that creates accurate gears and there is...
Type: Posts; User: Jaguar
It is considerably faster to draw in Ironcad as opposed to any thing I've ever used and that includes Solidworks. Threading is faster, there is a gear module that creates accurate gears and there is...
Look in the Blue book that is supposed to be in the electrical panel. The initial parameters will be there
EZ Cam is really good software, especially for the price.
J
You can post a metric part with an inch post and run the machine in inch.
J.
G code Pocket and facing routines are already there.
J.
Have you measured the spindle temps?
J.
The phase converter will be problematic. If the machine costs anything at all it's too much. There are no parts available for the most part and this machine is notorious for blowing the servo drive...
The red keys tells me that is a new machine fresh from Doosan. Get some local help. This is what you paid the money for.
J.
Good point.
Yes it has a tape button. The DNM400 is setup to run DNC right off of the PCMCIA slot on the front of the control. Based on the way this conversation is going I would suggest the OP get some local...
That may be an interlock alarm as in one of the prox switches isn't reading a position and the ATC doesn't think it is safe to rotate. I would call my local Doosan tech to come out and fix it.
J.
You might want to try an M190 between moves as it is not advisable to do a rapid move with the sub spindle clamped.
J.
Dude, it's like night and day difference. The Mynx will take cuts on a day in and day out basis that the VF-3 won't even touch. There's no comparison, the Mynx is a real machine while the VF-3 is a...
That would be in P1241, the G30 Parameter.
J.
Since you are in India, the Doosan/Daewoo dealer can provide them to you since a DMV 400 hasn't been produced in a long time.
J.
Ger the parameters out of the back of the machine in the blue book.
J
There should be macros installed. Those parameter also show or hide 8000 and 9000 programs.
J.
Do you have a picture of this machine with a Doosan label on it? I've never seen one.
J.
Probably a Keep Relay. Consult the Blue book in the back of the machine.
J.
P3202.0 is probably set to 1, set it to 0 and you will be able to see the macros.
J.
Why would it matter where G54 is on the machine? Make the part origin the G54 location in FM and then set that G54 anywhere on the table that you want. Your machine really shouldn't care where the...
I don't think they have changed much from the 18i. Be careful when you try these just in case there have been some changes.
O9010(G300 TORQUE CONTROL START)
#3003=1
#1100=1
#2=FIX[#2]
G04...
The Doosan dealer is the one that can give you the best most accurate information. The documents are there, not here on this forum, although I have them but you need to ask YOUR dealer to put you in...
If you want to use polar mode the command is G12.1 to turn on and G13 to turn off. All this information is available through your local dealer. Call them and make the salesman get off is a$$ and...
Rather than asking on the forum just ask the Doosan Dealer that sold you the machine. They have all this information available in a succinct manual and it is fully explained in that manual. Very...
Sure. Stop the tool changer with the E-Stop, change to the Custom 1 page and go through the toolchanger recovery routine but don't let it complete unless you want to drop the tool once the arm...
The formula is: RPM * PITCH = <160 IPM
Should be an 18 or 21 unless it is a new one.
Did you get a manual or training with the machine?
J
The yellow books are the Fanuc books, you want the BLUE book out of the back of the machine electrical cabinet. Did you turn on the low pressure clamp when you machined the holes?
J
What control?