Search:

Hello
You can read out the IP with the key number NET123.

I don’t think that error message is related to the kinematics.

Usually you don’t have to change anything in the parameters for that. I would contact the machine manufacturer.
In the worst case...

Hello and welcome
Cycle 19 on a Heidenhain processing plane means swivelling. Give us a few more details about your controller.

Hello Lars
As far as I know that only works with the full version.
With the demo version, only a few blocks are saved.

Hello
I know it from my younger years.
In principle it’s not a bad scheme but the “personal reference” still plays a vital role!!
The superior still says how things are done and you need to...

Hello
Are all folders empty? Have a look under file type “all” if there are still other files in the folders.

Hello
Do you often clean your keyboards with liquid cleaner? Does coolant splatter often gets onto the keyboard?
These could be reasons for the premature effect.
Otherwise I don’t think there is a...

Hi

Where Solid CAM is installed (folder SolidCAM) there is a .exe file called chooselanguage.exe- there you have to click onto German.
But just for your information: You can change Solidwork to...

I think you might mean Solidworks..

Change units under : extras, options, document features, units

The easiest way would be to mill a finish cut with a measured miller. Then calibrate the Z axis on the milled surface with your sensing device.

Hello
Can you post the whole program please?

Hello
Yes, I know the problem. The data transmission used to work without problems and since I got a new computer it doesn’t.

I also used Remo however the Mash was connected over the network....

Hello usually you should have the original CD of the software, shouldn’t you?

Hello
With the Heidenhain, the cycle 395 is a partial pre-control..I have never worked with it... but I think it has nothing to do with your processing plane, doesn’t ?.

Hello

I would use cutters for aluminium, uncoated and cut as less as possible.
I think roughing cutters are not necessary in this case. It’s more important that they don’t produce any heat!

Thank god my friend did not get the machine in the end

Calculating the angle :

Set the first point as reference point, drive to the second point and the you will have the X and Y value, then opposite leg divided by hypotenuse and with that you get the...

Hello

Might be the scale of the Y axis

Hello
I would try to connect a rack with magnets onto the crack and align as you described with cycles.thumbs-up.gif

Hello

You should be able to open the file using the direct interfaces of NC work.
However for the interface you need an extra license.

Alternatively, you can save the files from Pro Enginner...

Hello
I would choose the longer path in x and the feed in y and z.
With a Rz of 6,3, I think that an Fz of 0,5 is very questionable. The step 0,6 is also the upper limit.
Just try it out. Nothing...

Hello
With my 530 controller it’s cycle 431.
The data is displayed in a separated file, with the file ending TCHPRNT.

Hello
Describe it a bit more detailed / a drawing would be bad either.

Hello
That sounds weird. Usually the material can be processed without problems unless there are many cavities or other inclusions in it. Have you checked the material?

Basically, you are correct but:
Exchange your sensor after the calibration, or rather 1-2 hours later and measure your true running again. I think your won’t be in µ anymore!!!
The machine...

Hello
I find 0.001-0.002mm far too extreme unless it’s a measuring machine!!! I had the problem with longer tracer pins that the Machines drops out as it though that the sensor is approached...

Helloo
Does nobody know that machine?
really?

Hello
Please describe your problem a bit more detailed. Has the tool got a registered length in the tool table? Do you call the tool number before the resetting? Or rather do you recall the tool...

Hello guys
An acquaintance of mine wants to buy a Dutch milling machine with a STYLE CNC controller Teach in. _Typ BT Serie.

Has anybody already had any experienced with it?
Attached a few files...

hello
what material is it?