I have a 2007 Haas VF2 and I am getting an error on start-up:
ENGLISH LANGUAGE NOT FOUND!
M1805ENA.bin NOT FOUND!
M1805ENA.lpk NOT FOUND!
COPY BOTH THE .LPH AND .BIN FILE ONTO THE USB STICK....
Type: Posts; User: hutch07
I have a 2007 Haas VF2 and I am getting an error on start-up:
ENGLISH LANGUAGE NOT FOUND!
M1805ENA.bin NOT FOUND!
M1805ENA.lpk NOT FOUND!
COPY BOTH THE .LPH AND .BIN FILE ONTO THE USB STICK....
I do not have those any longer.
391350 I had to add compensation to the lead in lead out and tweak the settings on the profile. There must be a default setting to make sure this is always on. I'll check.
It looks like if I use near zero "D" offsets this will run. This post processor looks like it sucks.... Is there a way to have it use actual tool diameters in the machine or only zero with a bit...
I have a simple profile and no matter what I choose on CAMWorks for Solidworks 2018 , the post processor will not get it correct. I am running this on a Haas VF3 and this actually calculates I and...
We had a part stick onto a drill and attempt to be put away into the magazine. Nothing is broken and we slid the part off the drill. However, the robot arm on the magazine did not finish it’s...
All this was a good find . The OSP-300 book shows Work Counter VWRKC[α, β]
I have never been able to get this to work. VWKCC[α] works fine with α being 1,2,3 or 4.
1: Work counter A
3:...
Thanks Deadly!
Those are great ideas. I did try to set the two before the transfer but there is an M151 code that synchronizes the B spindle to the A spindle using 2nd spindle zero offset in the...
We changed the “A” – Left Chuck to grip the points.
When the IGF writes the program it uses the M151 to sync the spindles. Does this use a parameter to set the “B” sub spindle angle ©? No...
We are having issues with our Renishaw RMP60 probe and the RMI-Q reader. The Okuma COntrol is an OSP-300
2395 Alarm-B User Reserve code 92 ‘PROBE OPEN’
We have swapped out the Probe and still...
The 3 balls had major contamination. Pounds of rust and dust in the cam tracks. While we had it open we replaced :
(1) 51-0152 BEARING TAPERED ROLLER
(3) 59-0616, BALL 1 7/8 APC
(1) 20-2110A...
Our issue was with the Okuma MA-500HII 642.191290 – OSP-P300M control has an alarm 1703-03.
In the Diagnostic screen when we are in Handle / Manual mode with the MPG we see
• Axis Interlock...
HSMExpress by autodesk is free.
Looking for help finding haas 2005 parts for an EC-400. The lift on the APC will not go all the way up and I think it is the cam on the inside. It looks repairable from the manual but I am...
Gates has some excellent "how-to's" on their site. I think there is even a calculator for center distance with each of the pulleys and belt. If you are using the same pitch pulleys and belts...
When I set-up a flat disc in the chuck and tram it in to zero on the indicator, the disc is not perpendicular to the X axis. It is cutting a convex part 0.004" high in the center of the part. ...
I am having the same issue. I will try these settings and report back.
Mori Seiki MSC-803 on a CL-203
THANKS!!!
1171 taprov Tap return
override
Set the tap return override value for the synchronous
tap.
1 to 100 (%)
1172 tapovr Tap return
override
Set the override value when leaving the tap end point...
Is there a machine parameter that would cause this?
FROM THE PARAMETER MANUAL
12 SYNCHRONOUS TAP CYCLE ACCELERATION/DECELERATION TIME
CONSTANT ERROR
The time constant has not been set...
molgora,
How are you send from Machine to PC - Device 0 "Punch".
I still have not found anything on this MSC-803 Mori/Mitsubishi control
(flame2)
Not_In_Use THanks, I will try that.
I did write the code out long hand ;
I CHANGED MY ZERO POSITION. The face that gets tapped starts at Z-0.500.
G00 Z-0.25
M03 S150
G63...
This is a Mitsubishi Meldas Control.
The link above just takes me to the Ebay site. Do you have a store on there?
All,
I am trying to Face Tap on a Mori Seiki CL-203B Machine. The machine goes in fine to the -0.625 point and then will not reverse the spindle and feed out.
I get the EX0401 ( G1027)...
Dano_St did you ever receive manuals? I am also looking for them.
½ - 14 NPT Male thread Inch Programming
Thread Pitch 0.07142 Thread Taper 1:16 on Diameter
Thread Height 0.05714” Root Diameter at start 0.6977
Root at finish 0.7485”
T0909 (THREAD)
G90...
319594
The only thing on the start-up screen. Is there somewhere in the control that I can tell which version it is?
319592
This is my control. It is an OT but I do not know what version it is. I am looking for manuals. Thanks in advance for any help.
319342
This is ours. We'll be tearing into it... It has voltage at the motor but no movement.