So it looks to be Chinese base with a KMT pump. The pumps I have worked on, buying parts and support shouldn't be a issue, its the base I would steer clear of, I'm not a fan of having to stay up till...
Type: Posts; User: MCPservice
So it looks to be Chinese base with a KMT pump. The pumps I have worked on, buying parts and support shouldn't be a issue, its the base I would steer clear of, I'm not a fan of having to stay up till...
1. More then likely you have some metal under the block in the rear of the tool calibration block. Take the block offf and clean under it and see what that does.
2. Multicam vac table design isn't...
Were you cutting metal?
So the system locks up when you choses the existing test files in PSS?????
Blink count 5 is normally a mechanical issue either your servo motor or possibly your bearing cars. I would with the machine off try to push the Y axis and see if you are able to move it with...
Did you set a static IP address for the PC you are using to communicate to the machine.
If you still have the old drive and it can power up you can if the machine uses a 2521 or never control board, use the control board to save the old parameters and upload to the new amplifier
open up th control cabinet and post a pic.
You have to program the drive to the correct axis, you might be able to call Multicam for the drive parameters.
You will need the teknics communication software and cable to talk to the drives or...
Check to see if the control board is booting up completely in motion mechanic, if you can see the system fully booting up then the issue is the keypad
which axis?????
https://www.interstateplastics.com/phenolic-plastic-sheet?kw=phenolic%20sheet&gad=1&gclid=CjwKCAjwt52mBhB5EiwA05YKo19KfYsEx-Zs-Kwc6kkbkLbUAnQCBa_zjGlbWBntheGTbpAfuqRpbRoCKuIQAvD_BwE
you will need...
You might be able to change parameter 60 to 2 but you might still run into the issue of not having the correct inits and firmware to run the system without the keypad.....
Multicam told you kind of half the story, Teknics is phasing out those drives but they have not yet. They will keeping building drives until all the parts required to build those drives run out.
...
What is the fault on the inverter?
John this is a time where you should have someone come in and properly set up and train you on the machine.
I'm pretty sure with a 2020 machine you did not get it for a song and a dance....
...
With the machine off....Check your Rio board connection ( Unplug and replug all of the connections on the Rio and that the Rio board is not covered in a nice warm blanket of dust....Electronics don t...
MultiCam Southeast | CNC Digital Finishing, CNC Plasma, CNC Laser, CNC Waterjet, CNC Router Bits
Give me a call I may be able to help you out....
678-548-1483
MCP Services
Maurice Phelps
If the drive is faulty the error will stay on the drive.
If the issue is cable or servo motor then the error will move from servo drive to servo drive
If the drive is faulty the error will stay on the drive.
If the issue is cable or servo motor then the error will move from servo drive to servo drive
Main spindle motor bear was damaged? Or the servo motor bearing was damaged?
IS this a multicam plasma or a ez cut plasma??//
There isn't any compensation for backlash because you can only turn out so much, eventually there is no number you could put in the controller to comp out.
On a Multicam machine you more then...
As a tech that has experienced various machines from multiple countries...my experience with Chinese machine have been challenging with the lack of documentation, 12 hour time differences to speak to...
Lifting Cable....you might want to upload some picture on the site here to give better idea of what you are talking about
You should be able to call Scanvec, if you have the Key Number they will send a link to download Enroute 6. As for the Multicam software how old is the 1000 series and what OS will you be using with...
Does K axis actually find home?
And you are using a static IP?
How are you connected to the router...
PC to machine
or
PC to switch to machine...
Ethernet comms