2012 VM2. Just recently had Haas install 1000psi through spindle coolant. The day after they finally got everything done, mill alarms out. When the mill stops the spindle (above 6000rpm), it throws...
Type: Posts; User: Solid_Brass
2012 VM2. Just recently had Haas install 1000psi through spindle coolant. The day after they finally got everything done, mill alarms out. When the mill stops the spindle (above 6000rpm), it throws...
Came into to work this morning with my Cadet 4020 (OSP 5020M) displaying units in Metric. Checked my parameters and found the "Data Set Unit", under the : "Input Unit System" page in parameters had...
I have another 4020 that is getting the spindle rebuilt that is going to be used mostly for heavy cuts in 4140 and 416, so I will defiantly be keeping an eye on the belt for slipping. Thanks again...
Thanks for the info. I ended up just putting the tension close to where the original bolt location was with the older belt. The old belt wasn't worn out by any means. I just put a new belt on since I...
I am new to Okuma, or Fanuc for that matter. I have two 4020 Cadet with OSP5020M controls. These are new to me. Had the spindle in one of them rebuilt. I am curious about the proper tension for the...
Had a tech come out and update the software. The tech called Haas and talked to one of their software guys and they had never seen this issue before. Seemed to go away after software update. It did...
Made a little video of the issue:
https://youtu.be/m5Cl72_oAJ4
My Mill is a 2012 Haas Vm2. I have been having an issue with the controller. After I would run a part, I would go to set up a new part. I would be setting the G offsets with my reinshaw probe. The...
My 2012 VM2 spindle is noisy and feels gritty when spinning by hand. It started 6 months ago and has progresivly gotten worse. It only has 1200 spindle hrs, with no major crashes. I assume the...
I have a 2012 VM2 with low hrs, side mount carousel. I was running parts yesterday, and twords the end of the day Alarm 622 occured right at a tool change. It brought the Z axis up to do a tool...
This just happened to my buddies new 440 that I am helping him with (just got delivered last week). I hit the dual boot button by accident, computer re-booted and spindle turned on. His active probe...
I am new to Tormachs, but not new to CNC (own a few Haas). A friend of mine bought a 440 and I have been helping him get started. Was calibrating the probe (active), and it said that I need to switch...
Sodick Wire EDM
Sodick Mark EX A280L Wire EDM.
Currently powered up and 100% operational. It is in good condition. Both servo controllers have been replaced recently.
Sodick Mark EX EDW...
Running a short program last week, got Alarm 849 twice, both during a tool change. Both times had to manually recover the tool changer. Machine is a 2012 VM-2 with low hrs. Both alarms occured within...
Just an update, I was never able to re-create the issue of it randomly losing the Z position. Both Haas and my HFO were verry helpfull. One thing that might have led to the issue that the tech that...
The length of the calibratin bar was from the spindle face to the bottom of the pin. Made shure it was spinning tru and that the bottom is flat. I re-calibrated everything and the number in the...
1) Yes, still under wrrenty. I did call Selway and tak to them, the tech was the one wo said it might be voltage issues, and was told to just keep an eye on it.
2) The First time I calibrated the...
I have a 2012 VM2 (all bells an whistles). I had an issue a few weeks ago with with it machining .009 too shallow, so I re-calibrated the probe and tool setter. Everything was good after that. This...