Thanks Ger
Sent from my LG-H990 using Tapatalk
Type: Posts; User: P.Passuello
Thanks Ger
Sent from my LG-H990 using Tapatalk
Hi Yves
I went through the PRO file and found the relevant part of the file refering to the plugin
[Hyplugin]
OnOff=False
AmpCB=False
Selectedport=COM4
Selectedbaud=9600
SelectedFreq=400
You have broken the most important rule of using shielded cable. Thou shalt ground the shield at one end only. Usually the shield is connected at the VFD end. Grounding the shield at both ends cause...
Hi Dan,
I have made a video on installing your plugin onto UCCNC which might help others installing it.
I don't know if you have a website where you will be hosting the plugin so in the meantime...
So I opened up the RS485 adapter tonight when I got home from work and had a look at it.
I noticed 2 things about it.
1st the metal case of the USB plug was not soldered to the circuit board. Not a...
Do you have a big enough hammer?
Cheers
Peter
Hi Dan,
The new Rs485 adapter just arrived in the mail.
I quiclkly grabbed it and went out to the workshop and installed it.
The spindle started with the correct minimum speed for the first...
I sure did. As per Dans instructions.
Now for some good news
I have tested and found the same speed changing issue with the Mach3 Le royaume d'eole plugin at baud rate 9600.
Given the maturity...
Thanks Gerry that's what I thought is meant to happen.
I am under the impression that the Sact is got by reading the VFD and then displays it in UCCNC.
If this is the case then how can it be wrong...
Hi Jack
Here are my settings.
Mine is a 2.2kw 220 volt 10 amp 400hz spindle
PD001 - 2
PD002 -> 2
PD003 - 400 (Hz)
PD004 - 400 (Hz)
The VI setting is analogue which is what it is currently set too. The other option is VR which is the POT but I can give removing the link it a go if you like.
I agree the frequency is the problem...
I really, really appreciate all the help you have given in trying to sort this out for me and others.
It makes sense that if I am the only one experiencing the speed issue then it is something at my...
Hi Dan,
Good news and bad on Test7
The Sact comes up as matching the Sset everytime.
However when you start the spindle it may or may not be the speed shown on the Sact that the spindle...
I finally understand what you were saying about the spindle starting even though the speed on Sact is 0
If I repeat the test after repowering the VFD it wont run because it doesn't have a speed set...
That's much better Dan It starts.
I installed Test4 into my XP laptop and it starts everytime so far.
I still have that odd speed update issue I showed in the video and I should mention that it...
Hi Dan,
I have spent the mornng doing some testing and here are the results.
All testing done using HYTest2 plugin
I first installed UCCNC version 1.2027 to see if it bahaved any differently...
Hi Dan and thanks for he help you and Gerry are giving with this. It is Baflling
Just to clarify the Sset field is already filled in on startup with speed of 6000.
About a second later the Sact...
I avoided that one. Didn't know if there were XP drivers available for that chipset or not but I use the Prolific ones on XP for work and they work fine.
I will be away from the computer for a...
Mine is a Compac 6730B
Intel Core 2 Duo P8600 Processor (2.40GHz, 3MB L2 cache, 1066MHz FSB)
15.4-inch WSXGA+ anti-glare (1680 x 1050)
Intel GMA 4500MHD integrated graphics (up to 384MB shared...
The neighbours probably think I'm crazy going out to the shed after midnight.
I checked theCPU usage and it peaks at 60% in both Demo and normal mode.
The Sact comes up before the spindle is...
Hi Dan,
Thank you for all your help with this. It is much appreciated.
It appears I have confused you but I have spent the evening trying to figure out what might be going on and I think I may...
Hi Dan,
Gave it a try and it still fails.
The VFD goes into Run but the speed remains at 0.
I put my cable probe to the RS485 and listen and can hear the bursts of data.
There is a constant...
Thanks Dan
I found the override field at last. The % speed.
While I have blown away the install but I can tell you the override value was 100%.
I also confirmed on this setup the Sset is 869,...
Hi Dan
Not having much luck
I have attached the new profile I have tested. It has nothing other than the VFD configuration on it using the HYTest2 plugin
I deleted UCCNC and deleted the UCCNC...
Sset is reading 6000 on the DRO. I'm not sure where the override field is to check it.
Cheers
Peter
Thanks Dan,
I haven't shut down today only restarted so will make sure I do that as well.
Just out in the workshop creating the new config now.
Cheers
Peter
Thanks Dan,
The field 20000 was the original feild number for Sact when I first installed the plugin 8.1 yesterday but changed it later on the 20050 for reasons I cannot explain.
I don't recall...
Hi Dan,
Gave the PC a restart and retested but no luck
Here is the info you wanted.
Cheers
Peter
[UserTextfields]
I have been switching between the 2 so will restart my PC and retest and get back to you.
Will also get the profile info for you.
Cheers
Peter
I just retested making sure I didn't forget to click the save buttons and restarting as per the instructions.
HYTest2 as before sets the VFD to run but no speed is sent to the VFD
HYTest3 as...