Hi all-
I currently have 3 hurco mills. A md1 with zero problems. A md3 that is moody, and a mb3 (early version of the md3) that I bought as a parts machine.
The mb3 is a complete machine,...
Type: Posts; User: scrambled
Hi all-
I currently have 3 hurco mills. A md1 with zero problems. A md3 that is moody, and a mb3 (early version of the md3) that I bought as a parts machine.
The mb3 is a complete machine,...
On my ultimax II once you load a program, I can press the graphics button located above the trackball, and it will show the path of the cutter.
Steve
Sent from my iPhone using Tapatalk
Are you sure the air is turned on?
Check the overloads on the motor contacter
Steve
Sent from my iPhone using Tapatalk
Adrian-
Keep me posted on this. I am also interested in doing this.
Steve
Sent from my iPhone using Tapatalk
Figured it out. There was a broken solder joint on one of the proximity switches. A little solder and all better .
Steve
Sent from my iPhone using Tapatalk
I am working on the md3 with ultimax II.
My problem is the screen says it is in magazine slot 5 for example. The magazine is actually at locations 6.
I checked the detector proximity switches...
No luck with mid west? Look on eBay. I have bought parts there.
Sent from my iPhone using Tapatalk
I got mine from Mid West Cnc. Ask for Dave Price
Sent from my iPhone using Tapatalk
Adrian- I have 2 Hurco machines. A md1 and a md3. They are both old and break. I have no choice but to fix them. I spent 18 years working on and fixing industrial equipment.
Steve
...
My MD 3 had a sticker on the inside of the door that identified most of the boards
Sent from my iPhone using Tapatalk
This is what I did . I have an ultimax 2
First I swapped the x and y inputs on the dual axis board and tried to move the y axis. If it acts the same, swap the inputs back, if the problem moves...
Bloke. I found a drive. Do you know if this can be converted to a max 32. I have had one person say yes, one say no. You are the expert.
Steve
Sent from my iPhone using Tapatalk
Bloke- I switched the x and y. The axis starts driving as soon as it is powered up.
When the servo was swapped, the problem followed the amp.
Can these amps be repaired?
Can the md3 be...
Hi all
I am tracking down an issue I am having on my Y axis on my MD3.
I need to swap the X and Y amp. Can someone tell me which card it is?
Here is a picture
Steve
I have a Hurco md3 that is starting to have problems with the electronics. A board here a board there. Starting to get old.
I am thinking about upgrading the electronics. Has anyone ever...
Is there a program where I can program my hurco ultimate 2 from a computer in conversational mode? Is that what you are talking about
Sent from my iPhone using Tapatalk
Jim-
What about the phase perfect phase converters?
I am wanting to get a hypertherm 125, and only have single phase.
Steve
On most VFDs there is a way to adjust the rpm speed. Try and find a user manual for your VFD.
Steve
Sent from my iPhone using Tapatalk
I was told that the reason they burn out is the differential between the mill on 3 phase and the computer on single phase.
Steve
Sent from my iPhone using Tapatalk
Phil-
Are you sure the voltage is correct?
Mine are 230 or 480 machines.
I use Dave at Midwest cnc to fix my hurco's when I can't .
If you want to drip feed to the hurco, then...
Does it have a card rack for the boards?
Sent from my iPhone using Tapatalk
SS126
Did you get this working?
Sent from my iPhone using Tapatalk
Here is where I attached mine on the terminal block. 1 red and 1 gray wire equals 12 volts .
Here is the picture
...
First you need to switch the editor to NC from conversational.
Then read the file
Then cycle start.
It is that easy.
I have to re setup all the tools when I change editors.
I have one of Jerry's USB gizmos and have it connected to my hurco md1 and md3. Works good. Easy to use.
Be very careful on what you connect to the rs233 port. I burned both of mine out...
Larry-
The servo drive arrived today. I reinstalled it today and That drive appears to be working . After the gantry moves about 20 inches, the other x axis drive faults. The error is...
Look in the parameter section. You can adjust the maximum I.P.M. The previous owner might have turned it down
Steve
Sent from my iPhone using Tapatalk
We'll it worked. I was able to thread some PVC pipe today. Tomorrow I am going to try 1.5 alum pipe
Steve
Sent from my iPhone using Tapatalk
Bloke
It worked like a charm!
Thanks for the help
Ben-
I can not find lead in/ lead out
Bloke-
What does in/tan mean?
Steve
Sent from my iPhone using Tapatalk