Hi Guys
Im having problems with my 2006 Doosan 2000sy Vison control turret servo driver dvsd-tt-14a-04. Seems that a small power transformer has burned out as showing in the attached photos.
...
Type: Posts; User: mroy0404
Hi Guys
Im having problems with my 2006 Doosan 2000sy Vison control turret servo driver dvsd-tt-14a-04. Seems that a small power transformer has burned out as showing in the attached photos.
...
I downloaded the file and took a quick look, I really like what I see so far. This information is helpful and much appreciated!
Anyone here running a Hardinge bridgeport xp3 or xr cnc mill with a Fanuc 18i-MB control. I need help with the location of the random tool registry, can't seem to find it on the control.
The manual...
I'm interested in what the part numbers are for these bearings. Could you post up this information!
I have a 2006 doosan 2000sy lathe that could use a turret alignment, the drill is not on Z axis center line but drilling at a slight angle.
I measure .004 over 4 inches. Seems simple enough, just...
Be sure your in Handle mode press the door open button on the control panel, now try the tool release button. This is how my 2006 Hardinge xp3 operates.
I has a Fanuc 10m modal A control that was FS3, owned it for roughly 12 yrs and could never get it to drip feed. I tried everything, it pissed me off to the point of selling the machine and buying...
Send me an email at [email protected]
I still have parameters saved from 2 Daewoo puma 8s machine's.
One was a 1995 other was a 1996.
Both had Fanuc OT-C controls.
Any post available for 2006 Doosan 2000sy with Fanuc 18i-TB control.
Thanks for any help at all!
Thank you for the reply STLMACHINIST, I will try this and reply back for other's to learn.
Help!!I need help guy's!
I recently purchased a 2006 Hardinge xp3 1000 with a Fanuc 18i-MB control and a nikken tilting table integrated into the control, this all works great but I need to remove...
I ended up using a 1/4" ballnose end mill with 5 Axis flow toolpath locked to 4 axis and follow surface pattern for the cut parameter. What really helped was to extrud the tooth profile in sections...
Hi Guys
I have drawn this worm gear and would like to machine it on a Doosan 2000sy with live tooling and y axis. In mastercam what toolpath would be best using the live tooling with a 1/4"...
Hi Guys
At work im running a 2006 Doosan 2000sy 6 axis lathe with a Fanuc 18i-TB control. When I post (from mastercam x6 with MPLmaster post) a face drilling cycle for the sub spindle the code...
Thanks for the input Hdowns
This is what I have tried.
Swapped the rs232 cable from another working machine setup. Still have the same results.
I used another computer that was once used...
I have a Fanuc 10m that has worked perfectly for years, today when I tried to transfer a program with rs232 the machine will not read any incoming programs. All else on the machine seems to work...
I could use all or any manuals for a 2006 Doosan 2000sy with Fanuc 18i-TB control
question,
I have been changing the 3.6 volt turret drive battery once a year, which can easily forgotten about. Then comes all the issues of reloading the parameters back into the drive.
...
I would like to add a NIKKEN 5AX-200II CNC TILTING ROTARY TABLE to a Fanuc 18i-MB control. What would be required to add this too the machine?
238256
Ok. This is what I found, one of the adjustment screws for the bottom gibb broke off causing the gibb to drive deeper into the seat. I have attached afew photos of the tiny 6 mm...
This is what I have found.
The gibbs on the B axis had the adjustment screws back out causing the gibbs to drive deeper into there seats. I have cleaned, lubed and adjusted everything. All seems...
Thank you for the reply CNCRebuilder
I took a look at the cannon plug and found it only has 4 large lugs, the other plug is much smaller, its plugged into the pulse coder. The alarm is over torque B...
I will keep this thread updated in the hopes that it will help someone in the future.
At closer inspection I have found the end of the ball screw has an 8 mm hex key slot, when I turned the ball...
Machine: 2006 Doosan 2000sy with Fanuc 18i-TB control
I was running a bar feed program all day using the sub spindle as a bar puller, all was running perfect no strange sounds at all. Then the...
Mclausen
Thank you for adding how you got your tape mode to function. I will also add my results soon.
Mclausen,
Could you please tell us which keep relay you switched in order to get the tape mode to work.
@ Don18P
I changed the Lithium 3.6 volt battery in the Vision unit, you may need to re use the plug as I have by resoldering.
Be sure to have the machine turned on before removing the battery,...
Post what alarms you have displayed, then we can help.
I have owned afew Daewoo Puma 8s lathe's in the past. Take a photo of the screen and send it to me at [email protected]
Mike Roy in Canada
In MDI mode type in s1000m3 then be sure to press th EOB button. this will add the %. your code will appear as s1000m3% then press insert. this will insert into memory.
Press the start button...
Would anyone have clear instructions on how to set the x and y axis zero for a 2006 Doosan 2000sy with Dog Limits. I do have instructions for the dogless set up, but this just don't work with my...