Hi Salih what is the serial number and the electrical diagram number
[email protected] Phone number 1 647 308 3375
Nick Safos
Type: Posts; User: NICK1945
Hi Salih what is the serial number and the electrical diagram number
[email protected] Phone number 1 647 308 3375
Nick Safos
Hi where are you located I can help you this is my email [email protected]
You can set it in the Bar feeder page after it has homed..............
Need procedure to set zero return on Dahlih MCV-500 on B axis I have APC 300 alarm due to dead battery
Yes what is the problem?
Hi on mdi or auto it needs to see the door closed and the chuck clamped............
Hi
For the machine to run in auto it needs the door closed and it needs to know that the chuck is closed.
[email protected]
Hi I can help you with those problems I also located in Toronto Ontario sent me an email at [email protected]
Hi
What is the model and serial number of that machine is it a Harrison Alpha 400 or Alpha 550. and what year is it
HI
I was out of the country i did sent you the procedures tonite
I have the parameters as fot diagnostics please tell me what type of turret you have how many stations?
The problem is you missing 24 V DC
There are two versions depending how old it is The first one had an E-stop board behind the main disconnect switch on the electrical cabinet usually the relay...
This fuse protects the +24V on the machine it means you are having a short on the machine wiring side check the resistance of +24V to ground and try to isolate the fault.
HI all
If any body needs zero return procedures for colchester or Harrison lathes sent me an email with the model number and i will sent you a procedure.
My email is...
Hi Kamal what is the serial number and is it an electronic triumph instead of electric i have a lot of info
Hi CNC Boss
i am an x 600 service engineer and i can sent you the procedure this is my email
[email protected]
Hi Gordon
If you open the encoder cover there are two white wires small gage going to the motor this is for the thermal switch normally closed you can check with a digital voltmeter they should read...
chances are that you moved the machine recently and you need to change the two phases in order to correct the phase .
I f you open the back you will see two hoses going to the spindle the big hose...
You have two plugs that plug on the screen one of them has the +24V and the other connects to the crt output from the control also check that you have filament light on the CRT
Hi try not to plug drawtube in the back of the lathe extra cooland might be shiping in the hydraulics through the drawtube threaded part that connects on the chucking cylinder.
yes i can get you the parameters you will also need the diagnostics
If you have two pins they will be in the front of the turret.
You might have a series of bolts in the front of the turret and if you loosen them you can turn the disk from side to side.
Or you have...
I am having difficulty in setting spindle sensor cannot orientate spindle rpm is good any help would be appreciated. especially a procedure for setting upthe spindle sensor....
also check the two pads in the back of the machine they will affect the column and those the squareness to the x axis.
you might want to check your parameter setings on your 0 T control
If a turret has been crashed you need to check two things.
1. Put an indicator and check that the face of the turret is perpendicular to the chuck when you move the x axis up and down.
2. Check a...
hi dbarath did you get your turret problem resolved if not give me a call at 647 308 3375
many machine tools act like that it is because it looses the turret position when you press reset. and you have to re-establiss a known turret position.
Looking for a procedure to align spindle sensor i get the rpm pulses but cannot get the orientation pulse any help will be apreciated or email me with a procedure. [email protected]
Hi the A axis parameters should be available from the machine builder Cincinati Troyke only provides theTurn table and the motor to match the 2100 control servo amp that you have. when you zero the A...