Hey did you manage to fix this issue?
Thanks!
Type: Posts; User: CSCPlastics
Hey did you manage to fix this issue?
Thanks!
Hi there, does anyone have M5PLCWIN software or a download link?
Thanks!
I need the spindle stationary to preform a ballbar test.
Thanks!
The G94 and G95 are a selected parameter on machine start up.
Unfortunately putting G94 in the same line as G01 did not work.
Thanks for your response!
Does anybody know how to get a Mitsubishi Meldas 520AM mill controller to G01-G02-G03 feed with the spindle orientated stop/locked M19?
Thanks!
The start of you program looks ok.
Can you confirm that you can input data into memory through this screen with your current settings?
If you can input data into memory with your current...
I would contact Mazak support and get the ball rolling with them in case no one here can help, surly they will be able to give you a copy based on the serial number on the machine?
If you are...
Do you have a screen shot of the program you are trying to send?
Well done, that is lucky!
I suspect the problem is a parameter that is causing an incorrect mode selection, which is causing the P1 error where
search is looking for the search criteria but cannot find it, so a time out...
Can you upload a pic of the mode selection switch?
Has the module got a fan? is it going?
Aside from the fan, don't waste your time trying to fix it, just get a new module.
I have attempted this before on servo modules, basically imposable to...
Is this picture with tape mode selected on your control panel?
I understand this, I was just checking to see if you can load into the machine memory, that way we can establish that the data is
able to be transferred before worrying about drip feed.
Is it...
Are you able load a small program into the machine memory?
Before changing any settings try and uses the start procedure I have put at the bottom
It may work by putting 1 in CMP?
If you are getting it to receive Data then I would say your Data bits, Stop...
What are your com settings?
For the machine and for the computer?
What DNC software are you using?
Hey Roger, I tend to agree with what you have said, thanks!
Problem resolved!
There is a machine parameter called BL this is for axis Back Lash.
When I brought this machine about a year ago it came with the BL value set to 255
It should only be around...
If you don't have a wiring manual then it makes it harder to quickly find the correct wires to test
Check at the back of the turret and find where the wires come out from internal micro switches...
Do you normally upload programmes into the machine memory?
If so then the DNC is communicating correctly and the settings should be correct
Describe your procedure when setting the machine to...
Sounds like a faulty micro switch or proximity sensor or adjustment.
Check the relevant switches are making contact when the error happens by using the diagnostic screen, I am not sure what the T-2...
Do you mean the tool parameters where the two angles are defined?
I have tried using any one of the standard tools 0 to 10 and custom tools, assigning various tool angles and rads and physically...
I have tried programming the part using the groove command, I think it could be used for a work around but I think the problem is something else.
I programed a real simple shape, where the groove...
Hey Bob, I have been working on another job, so haven't been able to try your suggestion, but as soon as this job is done I will try it and post the result.
Thanks!
Regards
Chris
I used the highlighted bar out, but have not tried the groove command
I will try the groove command.
Thanks for that !
Regards
Chris
I have tried assigning different tools with different tip rad's.
The radius in the part is a 3mm rad in the low area and the small radius at the top is 1.3
I have tried assigning no...
I have a Mazak QT10 with a Mazatrol T1 control, The problem I have is when machining the part, as per the picture, the
display shows the part is programmed correctly but when the part is machined...