it does the same thing that your other software does. you just direct your output to where you want it to go in the set up of solidcam . if editnc is its own program just send it there you could use...
Type: Posts; User: axis
it does the same thing that your other software does. you just direct your output to where you want it to go in the set up of solidcam . if editnc is its own program just send it there you could use...
no didt say the pull stud tourqe at the tool holder is wrong. i sead the pull stud tenstion holder in the spindle its somthing not alot of people check it. i am in know way saying that you dont know...
you cant take feeds and speeds off of one machine and just put it in another.every machine is different the speeds i can run on a haas i could dubble on the okuma. you may know how to write g code...
i would trade it in and by a new okuma. if you think the service is bad wait till you start comparing the haas to your okuma. i love my haas dont get me wrong but if i could afford a okuma.....
i run my machine at 6000-8000rpm in all kinds of material.with cutting tools from .05"to 2.5" if you use the machine and understand the limitations the tm can be a good machine. i feel comfortable...
thats a good idea if its a new spindle but if you have been running it for a year your not going to break in the spindle anymore. i run at 8000rpm all the time on my tm and have done since about 3...
if it is already been run and isnt a new spindle a warmup program should be all you need when you start the machine up, if it is a new spindle i would leave it alone until warrenty is over. the...
find people that use the software not the company tryin to sell it, it may look realy good in the demo but the learning curve is nasty on some of the software that i have seen.
if you are looking for a post for visual mill go to the mecsoft home page or make one yourself in the post creator in the software and this post is getting a little crazy if you need a post call the...
i am from canada and can tell you over the last 4 years the suport from solidcam has improved ten fold they have some new people there that are very good at what they do and have fixed every problem...
asking for stolen stuff on the net this is a good idea. there is no way anyone will find you here
its bad enuff i have to fight for work with every home shop guy now i have none profit machine shops life just gets better every day, your machine time is 25 hr i cant hire anyone for under 30bucks...
i desided to put a toolchanger on after the fact, i looked at doing it myself but the time i would put in learning how to put the toolchanger on the machine was more expencive then getting the haas...
what happend pls update
depends on the age of the tm but this happened to me and it was the big o ring inside the tool release they get old and crack or in my case it got old and bloated from the grease inside and couldnt...
solidworks has some issues i would wait a little longer couple more service packs i found that out the hard way with 64bit cant make money if the software dont work
one of the first things i did when i got my tm1 was take off the motor cover and reroute and put a new grease nipple in on the far side now i grease the right side left side and the ballscrew haas...
are the tm1p spindles not grease packed , like the tm1. if they are oil feed then air will come out the set srew on the side and out the bottom of the spindle the tm is also famous for sticking tool...
the time depends on the tools you have if your using hsm the setup would be the big time taker mabey a 4th axis would be good idea
the tm1p should have no problem doing this part with the tm its more the operator and setup then the machine. i would still spend the money to get into a vf but if money is a problem the tm is a good...
no dead or live center,if you have an air dryer every machine should get air from there i dont think your machine will need it but you will need an air gun,why you need a 12" chuck a 10" should be...
which dealer is the nearest to you that will make it easy service is key if it takes a tech 1-2 days to get to you, that is time down. i know this will sound stupid but what about a okuma they have a...
IF its a side mount the software will put the tool in place that it will remember you dont need to. if you want to know were the tool is go to the tool offset page and the info is there this system...
if you have that much error, it must be backlash and it isn't going to be something that you are going to be able to correct with any type of compensation, and you are going to have to reseat your...
for 1000 bucks i would expect no more that the experiance you had. most people just hear cnc and think it will run like the big boys. the machine is what you would call a starter machine the one you...
here it is you will make more money working for someone else in van right now. the need for machinest is so high you dont need to take the risk in running your own shop and spending your own money....
what year is your machine and can you put up the web adress for the vidieo
STOP WHAT YOU ARE DOING CALL A TEC
the only thing that you can t be add on after is tsc and sidmount tool changer as far as i have been told
i got the solidwork translator and it has never worked, it donst keep up with the updates and i have to up date solidworks to keep up wtih my customers.not happy with that