Hello, Is there anyone in the United States that still uses a Siemens Sinumerik 802C Base Line controller? Anyone? Or do I have the only one that ever made it to America? If you do have or had one, I...
Type: Posts; User: erikh206
Hello, Is there anyone in the United States that still uses a Siemens Sinumerik 802C Base Line controller? Anyone? Or do I have the only one that ever made it to America? If you do have or had one, I...
Hello, Is there anyone in the United States that still uses a Siemens Sinumerik 802C Base Line controller? Anyone? Or do I have the only one that ever made it to America? If you do have or had...
Hi, Can anyone tell me how to track down a PLC alarm 700024 on a 802C controller? The alarm reads, TOOL NOT FOUND, MONITORING TIME UP. I am trying to fix the issue but the manuals do not specify...
Hi, Can anyone tell me how to track down a PLC alarm 700024 on a 802C controller? The alarm reads, TOOL NOT FOUND, MONITORING TIME UP. I am trying to fix the issue but the manuals do not specify...
Hi, Can anyone tell me how to track down a PLC alarm 700024 on a 802C controller? The alarm reads, TOOL NOT FOUND, MONITORING TIME UP. I am trying to fix the issue but the manuals do not specify...
Thank you. We had not found that particular thread yet but it looks promising for sure!
Hello,
Our shop just purchased a 2009 PM1330 CNC lathe with the Siemens Sinumerik 802c controller. This machine was in storage for the last 5 years and fired up just fine. Problem, the controller...
Thank you, Yes I talked with Siemens support and they finally gave me the word ECHTZEIT, I believe this one should be above SUNRISE, EVENING and CUSTOMER. I have no alarms, the machine will even...
Thanks for the link. no clue about a jumper, looks like I can set the start switch located inside the controller to #1 position and this will do a default factory boot up. The down side is that I...
OK figured out the PM but error says your message box is full..... :-)
could you refresh my memory on how to do a PM? thanks
Thank you but sunrise did not work. Can you explain anymore about a possible "key lock" you mentioned? thanks!
Thanks but that didn't work either...
Hello, I just purchased a 2009 Precision Mathews 1330 cnc lathe from the original owner. This machine has the Sinumerik 802c controller. Power up, homing and jogging all work fine. When I try to go...
Thank you both for your replies. Turns out I was trying to restrain the step wall only. I failed to notice you must have a box set up and not just one line for a boundary. Once I created four...
Hi,
I have some parts to surface in V24 that contain a step wall. When I try to add a boundary at the step to keep the tool away (.500 ball nose) the tool path vanishes. If I remove the...
Hi all,
I am looking at several 2008 Fadal FX 3016's. 2600 to 4500 spindle hrs. Can someone who owns and operates one give me the straight scoop on this machine? Looking at small run jobs of...
P&S says the Delta 40 does not have a Eprom but instead has a FLASH.... They are sending info on getting into the par. and checking some #'s out. Stay tuned.
The X motor was just rebuilt when I got the machine so maybe they swapped encoders (encoder on the end of shaft or is it the part with the brushes?) Also, the mother board on the Dynapath was...
Can you tell me what the prom is? Good idea on the scaling, I will try that if needed. I will also check and see what it cuts in a manual mode using the screen as a DRO. I will report back soon. ...
Hi,
My J425 Tree gains about + .025 per 12" of cut part in X. The Y loses about -.008 in Y. Scaling is set a 1.0 and the drive belts have been replaced per underthetires recommendation. Can...
OK, the belts are on and so far the repeating looks much better. Mr Under-the-tire, I tried to reply to you but your message box is full. Can I PM you some other way?
Thanks,
Erik
OK, the belts are on order. I bumped the stop .02 and it still missed the mark by about .1 when I powered up the 2nd time. Third and fourth power ups homed in the proper place. Bumped it another...
I guess I should have listened to the salesman better......
Thanks again.
Wow, never would have thought about the belts..... Anything special I should know before I order some? Tension? The ways and ball screw bearings are lubed good, everything is dripping all over...
Hi,
This would be part to part I'm concerned with. In the morning, X homes where it should but Y can be off by .100.... I always re-dial x and y on start-up. I know I shouldn't have to but...
Ok, I looked at the help/lic. page and level 2 and 3 are not checked....... neither is the virtual simulation high-lighted on the modules bar. Shame on me. :-)
Thanks guys for the help!
Hi,
In V24 Mill, I would like to use the advanced (blue icon) Predator that came with my package. My files will not run period. Can someone walk me through the process of using this feature?
...
Hi,
My Tree J-425 with Dynapath 40 controller runs good but with a snag. Every time you hit cycle start, The machine does not go to the same place twice. Machining a part that already has cut...
Hi,
My Tree J-425 with Dynapath 40 controller runs good but with a snag. Every time you hit cycle start, The machine does not go to the same place twice. Machining a part that already has cut...