What was the solution?
Sent from my iPhone using Tapatalk
Type: Posts; User: newman55598
What was the solution?
Sent from my iPhone using Tapatalk
They are usually very helpful
Sent from my iPhone using Tapatalk
Have you tried calling milltronics?
Sent from my iPhone using Tapatalk
You might look at the Milltronics machines also. Their tech support is too notch even if the machine is 20 years old. They still support most of their machines. If you find one get the serial...
351042
The wiring is per the instructions from the Yaskawa manual. Maybe I should have said piggy backed instead of jumped. Anyway I did some more testing after you mentioned the wiring and as...
Yes there is power across L1c L2c when E stopped.
Sent from my iPhone using Tapatalk
No voltage across L1 L2 L3.
Also tested the relay as the Estop was being pressed and all phases are dropping at the same time as far as I can tell with the voltmeter. I'm not having this issue...
I have been working on installing a 4th axis on a Milltronics VM17 with cent 6. X, Y, and Z are sigma I on the 4th axis I have a sigma II drive and motor. When I power the machine on every thing...
There was just a milltronics t14 lathe that sold on eBay for 2250.00. Plus a phase perfect. You would be less then 6000
Sent from my iPhone using Tapatalk
Why not buy a phase converter and a used machine for less money?
All the info is in the link that i posted read #16. You are changing the special flags parameter in the centurion control software. Doing it using byte parameters allows you to change it using...
In MDI enter the following (Enter after each line.)
P99=pb208
Pb208=0
Pb81=2
Then to set it back to normal.
Pb208=p99
Pb81=0
Read this thread. http://www.cnczone.com/forums/milltronics/164565-cent-7-gcode-help-2.html
No the trig help is in the control. It is used by the conversational programming. If you are using cam you don't need it. However it would need to be on if you have a probe. Not sure if cent 5 is...
Not sure about cent 5 but in centurion 6 I had to disable the trig help when using my cam or I would get random errors (radius to small) and a few random cuts.
Fyi I had some trouble locating a serial to USB adapter that would work correctly. Went through 3 of them to find one. If I recall correctly the ftp chipset is better as the other one (don't recall...
Some say it is possible to run USB on dos. There are a few web pages out there on it. However I haven't taken the time to try to get it working. You can get a floppy emulator ( I believe sportybob...
If you are able to write your own macros.
Sent from my iPhone using Tapatalk
I think there is an add on for flash in Firefox as I have it disabled. However YouTube still works fine for me. Having it disabled stops most of the video advertisements when browsing the web.
Is it a high quality corn cob end mill? How aggressive are the teeth on the end mill? I used a none brand name end mill that caused crazy chatter. Changed to a new brand name end mill and problem...
Cncguns
Sent from my iPhone using Tapatalk
Are you able to save a text file from the machine to the thumb drive? Most drives on cent 6 machine are floppy emulators that require the thumb drive to be formatted to 1.44 MB. If you are able to...
Suncoast precision has treated me well.
Sent from my iPhone using Tapatalk
Put an indicator with a magnetic base on your table. Put the tip against the smooth shank of the drill bit and slowly rotate (by hand)
Sent from my iPhone using Tapatalk
...Straw with a jet motor attached blowing through an air conditioner to properly cool the air.
Sent from my iPhone using Tapatalk
I would disagree if I buy one type of material and all of a sudden it's not cutting the same and everything checks out on the machining side that only leaves the material that could have changed....
Check the spindle run out. Verify the RPM and Feed. If all of that checks out I would guess you got a bad batch of aluminum.
Sent from my iPhone using Tapatalk
I think you have a sensor tripped.
Sent from my iPhone using Tapatalk
The changer on mine doesn't home other then after using the cw and ccw tool change buttons. After power down and reset it remembers the previous position. This is not to say that the machine doesn't...
Can you load the tools with Gcode? Start by going to mdi input t1m6 that will take you to tool 1. If there is a tool in the changer it will be loaded into the spindle use the tool out button to swap...