Here is the IO information that I have.
Type: Posts; User: g-code_junkie
Here is the IO information that I have.
I just looked at the attached program and noticed that you are calling tool t1100 in g821 mode that mode is for the t2100 series tools. I do not know which series of L16 you have but I have attached...
Just an observation, on citizen machines both dollar signs are contained in a single program not two separate programs.
hope that helps
Just my personal opinion but the swiss style have a guide bushing that will help you achieve the tolerances you are trying to hold instead of just the collet system alone.
Hope that helps
most likely an option at that time.on some older models some options could be turned on in the control and some had a cartridge that would have to be upgraded.if it ias a fanuc control they may have...
Citizen Machinery UK - Sliding Head Lathes, Fixed Head Turning Centres, Citizen Lathes, Miyano Lathes, Autoloaded Lathes
above is the link to cnc wizard
usually done in sub after pickoff. Radius on front id of collet.Knurl blank in backwork block or in gang.
I have used a bump knurl holder with knurl blank .
see attachment.
good luck
All you have to do is make a threaded extension that fits in the front of your existing knockout pin(if it is a standard one)otherwise you can make a longer knockout pin.Either of these options will ...
I have used both rotary and and stationary guide bushings. Today most machines come standard with a rotating gb.The one feature on some of the stationary gb's that l really liked, was the ability to...
Usually in that situation I would use a standard er20 holder with a global or other toolholder bushing.
hope that helps,
I have attached the settings for L3 and L5.
hope this helps
If you have Win-Cnc ,under the the threading program section is a application that will write you the turn ,thread, turn code you are looking for by filling in the required information.
Good luck
I have used both Fette F-01 heads and Landis cnc style in the A & L series machines.
select origin key
then jog feed each one seperately in the order of xh,xv and then z
confirm that the origin lamp is lit when completed for each axis
good luck
These are usually set 16kpa min 24 kpa max with a nominal of 20 kpa. If you have an incoming of 17 kpa then it is, most likely, tripping low limit.If you have the A-20 with a C-320 loader there is...
In the past I have sealed collets by making a fixture that matches the collet sleeve and cap.I then tighten the collet onto a gage pin,fill the slots with silicone and let set overnight.Usually any...
first drill pilot hole 1.5 to 3xd.
position gundrill inside pilot hole before turning on hp coolant.
may have to start spindle after in pilot.
when done return to starting depth in pilot hole....
If you are grinding the tools then thread @ 800 rpm and put the allowable flat on the point for the thread you are trying to cut.I put 6 to 8 degrees for clearance on the cutting angles and flat.Also...
first zero return the loader and then check the switches or prox sensors .
good luck
I have set the angled tooling on a comparator,vision system or even a cmm what ever was available.
good luck
even back in the cam machine days we used to spin the oil out of the chips and now on the cnc's. It saves on oil loss and in some cases increases the value of your chips due to the minimal amount of...
Normally I store my progams in folders seperated by the machine type and also save the parameter file in each folder.
good luck
BARFEED SUB PRG
O2011(CHANGE BAR )
$1
G98G1X#814+#815F50.
M3S1=500
W-2.
M7
G4U1.0
M55
M6
Mitsubishi,ceratip and ntk inserts come in those sizes
goodluck
turn a short length and then support with sub or one of the 21-23 stations (g650 or g620 mode).I sometimes have to use a lower rpm in order to cut down on vibration depending on how straight the...
This is what is in cnc wizard-just fill in the information required marked by an "*"
(DEBURR CROSS HOLE C AXIS)
(#510=DIAMETER OF CIRCLE)
#510=*
(#511=TURNED DIAMETER)
#511=*
(#512=CENTRE OF...
If you are using round stock then machine the part and complete the milling of the square then stop machine(do not open main collet).then you can perform the phasing prodcedure to store the...
check your ols1 and ols2 and see if they are tripped ,if they are then reset them