Hi,
I turned my machine on today and the x axis has a buzzing noise. I put the video on a machinist forum and the guys are saying that the servos are dithering and I need to adjust the gain on...
Type: Posts; User: technetics
Hi,
I turned my machine on today and the x axis has a buzzing noise. I put the video on a machinist forum and the guys are saying that the servos are dithering and I need to adjust the gain on...
Hi Everyone,
A couple days ago I was running my machine and the z axis started loosing count on a drill cycle. Soon after that the e-stop started to trigger. Just before the e-stop it sounds...
Hi Mike,
The machine is a Cincinnati Arrow 1000
Running on A2100 Control
With an integrated Troyke DL-9-B Axis
Thanks again
Shaun
Hi,
I've had this machine for a couple of years now and I've never used the 4th axis. There are a couple of parts that I'd like to cutout using this. I've entered code and hit the start button...
Hi Mike,
Thank you for your help. I will give that a try. Are the grease fittings for the thrust bearing along the front of the table? I live in Penticton BC.
Shaun
MIKE CNC Machine...
Hi.
I have recently been running my arrow 1000 and I've noticed that the y axis has a grinding/pinging sound. Ballscrews? Guides? I have no idea where to start and get parts. Any help would be...
I fixed it. The circuit breaker (CB1) has a feedback switch in it. There was no continuity between the switch in either position. Making the machine think the breaker had popped.
Shaun
Hi Mike,
Thank you for the reply. How do I reset the overload? The circuit breaker (CB1) has not popped. If I push the bypass button on the pump relay (M1) the pump will work fine.
Thanks...
This morning when I turned on my machine I got an error Alarm 39-14 "Coolant motor overload" I pushed the bypass button on the motor relay and the pump will start and I can't find any breaker that...
It looking like I'm having the same problem here. I haven't removed the battery at this time. My bios version is 1.00.13.CV2 . Any help would be greatly appreciated.
Thank you
Shaun
Ok I'll try that. Thanks for your help.
I had my machine transported and the table came loose and crashed into the tool setter. I replaced the probe but now the tool probe center is out by about .250". How do I adjust the center?
Thank you
I moved my machine a couple hundred miles and I think this has caused the problem.
I had a problem with the y limit switch it was stuck. I had to hold the green button to move the table.
Now...
Hi,
I have the exact same problem on my machine. I'm not quite sure how you went about deleting everything. So you hold the CTRL button while using the up and left keys and then delete?
Thank you
Thanks for your help. I found the previous post. I'll give it a try.
Hi there,
I have a Cincinnati arrow 1000 with the acromatic 2100. Ive been having this problem for a while now. After the machine has been on for a couple hours if I put code into the MDI it tells...
I installed the new power supply and it worked without any problems. I now have a problem with my tool probe (Renishaw model TS27R). When I when to do a tool measurement the spindle didn't stop and...
Thank you for your input. Its greatly appreciated.
Shaun
I was cutting out some parts and the machine shut down due to an error. The error reads,"Malfunction in the power supply for the control system causing the realtime processor to reset and restart." I...
Hi,
I have a Cinci Arrow 1000 with a2100 control. I can't get the post to interpolate. I've tried different letter and g code entries but with no luck. Does anyone have a post for mastercam X3...
I just had this problem and it turned out to be the real time board. Hope this helps.
Hi,
My Real Time Board P/N 4 3424 2169A03 packed it in. Does anybody know where I can get it repaired or replaced for a decent price?
Thank You
I've sent the processor away for repair. Thank you everyone for you input. It was a big help to steer me in the right direction.
Hi,
It looks like I've bitten off more than I could chew here. The techy changed both batteries. (I didn't get your reply until after) So this probably means that the factory bios settings are...
Hi,
Thanks for the reply. It was a busy day with nothing accomplished. I changed the hard drive and the batteries and now the screen doesn't come on at all. I talked to one of the techies at...
When I switch on my machine it starts up as normal until an error of 'time not set" You can either press F1 to fix the date or ESC to ignore it. Either or the machine starts to boot up the and then...
Sorry,
I guess I should of given you more information. I'm using mastercam x3 software. I had a similar problem with the post not setting in the z value when the home position is entered. It gave...
Hi Everyone,
I'm new to the cnc world and am having problems getting the machine to interpolate.
Line of code:
G02 X 1.8077 Y-.7228 I 1.8 J-.713
Error message:
"End point off circle"...