Search:

Use 6366Rev/min and 630mm/min.
A stable clamping is vital because otherwise the cutter breaks due to the vibration.

When it swings open then it’s best so use a small VHM cutter.
With the correct strategy, you won’t be slower than if you would use a big measuring head.

We have Ultimax 4 and Winmax, with both its possible to set up a FTP server- there you can access a FTP manager.

I would think its similar on the Ultimax 3

We mill flame-cut parts with WSP for stainless steel. We have made good experience with it. Vc has to be adjusted according to the hardness...

So I guess 5 axis processing is not possible and you don’t have a second machine with a horizontal spindle.
If the requirement of the part is low, then I always adjust it with a hair angle, when I...

Often you can only use them from H8 onwards

I have a FUW 250x710. For private purposes.
It will be a bit different to your one... what error message comes up?

Well generally speaking the SR series has 40, the VTX-U 48 or rather 96 tool slots, the VMX 30 only 24 - in case that’s important.

The VTX-U has almost double the torque than the SR and that with...

I think you will have to contact Hurco directly. I also think you should consider the VTX-U because that the only true 5 axial machine from Hurco... all the others are only standard machines that are...

Do you want a pure 5 axis machine and do you not need the free table like on the SR series apart from the rotary table?

What about the clamping surface? The Die SR has Ø610 the VMX30 only Ø250.7

I would only pre-mill and then unscrew. Alternatively with an extra finishing cutter.

Grinding allowance depends on the tool: I would choose between 0,1-0,4 mm.

I've just downloaded the latest demo.
So according to it, it should work.
You can find it on the software in the same in the same way like on the machine:
Utilities / User Settings / Quick CI....

You can save it on the machine, but I don’t know if you can read it in on the PC as I only have a demo version from 2003

I think WD40 is not very suitable as it’s too thin and one of the most expensive alternatives.
I guess you have many small recurring parts ..

What stops you from leaving them in a container...

What are you doing so far?
I would oil them...

Are oil and room temperature identical? I would imagine that the viscosity also has an influence on the flow.

Can it even be compared? I would think your personal machine is not running as often.

It could be a filter that is dirty.

Yes, the parameter programs are meant.

We handle this so that the essential parameters are never changed.
If we now want to mill the pocket loop, we add the "parameter change" before a sentence,...

If your cutter is a bit bigger than the radius of your pocket then you can write directly over Helix “lines and bends”.
If your cutter is smaller and the pockets are supposed to be cleared as...

My training is not until January.
But I think you have confirmed my fears:
That this short time is not sufficient.
I have already read the instructions for the 5-axis milling,
but this mix of...

Have a look here

http://www.rotoclear.de/en/index.htm

Well, I see it differently.
Multi tasking machining for me are a turning- milling centres where the revolver is amended with a cutter spindle and also the tool holder are clamped into a HSK or...

I don't know this typ of machine, but perhaps it is the sliding contact (if the machine has a coupling.
By the old machines from Heckert this contact looks like a spark plug with plastics outside.

Have a look at ‘Hahn and Kolb’ they used to sell them!

I do it like this: I first go from X0/Y0 until the 2 radius central points of the groove and then note the measurements.

That way I eliminate the annoying calculations.


You don’t need more to...

Hello Zaab!

You don’t necessary have to get the pump for the same manufacturer. Have a look at the performance data and buy the pump somewhere else. In German tool machines, there often use pumps...

If the file isn’t too big, send it to my e-mail, I’ll convert it in Tops and send it back to you today.

Well, I do something like this several times a week.
I use a simple VHM end mill Ø10.
In my example I use your R15 and assume that the radius goes over the Y axis.

Segment: 0
X Start: -6
Y...

Well, we’ve had a similar problem with our VMX with Ultimax3. The processor was down the drain.

Yeah, there’s a demo version.
I’d be glad to send it to you.