I can send you some manuals and schematics for it.
Email me at [email protected]
Type: Posts; User: tpodgwaite
I can send you some manuals and schematics for it.
Email me at [email protected]
I have gotten a a couple of those drives uncorrupted and going again by connecting to a PC with a USB tp IDE adapter then running scandisk and check all the fix errors boxes. Sometimes it works. ...
Check CMOS settings in the COM port area. I believe the manual panel was connected to COM1
You are spot on as far as it is a 5v TTL input. Just have to dig up an Anilam diagram that shows hookups.
Not a stretch at all. I used to work on a lot of them. Send me a msg w your info and we will try to get you fixed up. - Tim
The 1100 will only run conversational type programs, in it's own unique language. There are only 2 ways to get a program to run in EDIT - DRAW mode or the actual AUTO and hit the green button START...
I would agree that the brake seems at fault. If that is true you may also see the overshoot problem if you try a tool change with no tools in spindle or pocket. When the arm comes in to grab the...
This is a little hokey but you could mount a small switch somewhere that when the quill fully retracts it closes the switch. Use that switch to close the index start signal. Dwell the control for an...
I could probably help you with it but you'd have to ship the computer to me here in Indiana.
Tim Podgwaite 317-600-9720
Yes, call a place called Measurement Technologies in St Clair Shores, MI. Ask for Don. He fixes/updates Anilam computers, among other repairs. I'd tell you to tell him Tim sent you but that might...
It's not seeing the IO boards, as the message indicates. Because it can't see any active inputs connected to the IO boards, it's issuing error messages as if the required input was missing.
Once...
For some reason M50 & M51 come to mind. One disables the spindle drive, the other enables again
It doesn't have one.
Change the F to 16 because it is asking for TPI, not the lead.
I'd bet it's a spacing problem. Those on board editors put each character in a specific spacing arrangement. In other words, Tool#1 does not equal Tool #1, and so on with every other conversational...
Hi Mike. I have a friend of a friend of a friend that knows somebody that can help. :-)
Call me and I'll send you what you need. Tim P.
If I remember correctly, I think it was a 187L050 belt. A 187L050 is approx 18.7 in outside circumference.
It is a 187L050 belt. Anilam/Heidenhain P/N 67200057 if they still have it. Try ordering through MSC. They used to deal with Anilam parts.
In the Setup Utility, there is a menu called 'Miscellaneous'. In there there is a parameter called something like Maximum Programmable Feedrate. Default was 80 IPM. You can set it as high as the...
It's tricky, but if you can get into the PLC menu then into the EDIT mode, you can look for a file called GLB_PLCCFG.DEF and look through the M-code section to see if there is a special M-code...
Hi Maxvic. I guess first I would ask if the lock ups and abnormal program terminations happen randomly, or only when you run across a certain line of code. Abnormal program termination is a...
No need to home to jog. No automatic home cycle anyway. Make sure silver toggle switch is in AUTO, not MANUAL. Pull out e-stop, press servo reset pushbutton on rear of console. Should hear click...
I have some info on the 1100M control I can e-mail to you. Possibly even some specific to the E-400 machine. Does this machine have a powered knee(up/down), or a manual hand crank like a...
What does is not do?
If you need anything else, e-mail me at [email protected] If you can, send a picture of the control mounted to the machine. As you noted in one earlier post, there were different versions (or...
my notes say the 1400M used 'LIMITED' as the basic password, 'SERVICE' as the service level password, and 'PLC' as the password for interface related items.
It is possible to change the password from the factory setting (Y10) to something different, but you can't change it back unless you know the new password.
There is a factory level master password...
Can it do a tool change after it stops in a G84? Or do an M19 spindle orient? I wonder if there is a problem with the reference mark on the spindle encoder getting through to the CNC chassis.
I'm not sure who can fix them. I worked for Anilam but that wasn't my bag. They were bought from a company called Glentek out in California. Anilam/Heidenhain might have replacements still. You...
Hi Steve, I'd bet 10 bucks that one of the output transistors of the servo amplifier card has gone bad, hence torque in one direction only. You can swap out the Z amplifier card for one of the X/Y...