I have a Haspa K24 spindle motor with a spindle thread of 18*1.5mm, depth of spindle is approx 20mm and hole dia of 11mm. which looks to be pretty parallel
Can anyone help me locate a Collet nut for...
Type: Posts; User: Georgie
I have a Haspa K24 spindle motor with a spindle thread of 18*1.5mm, depth of spindle is approx 20mm and hole dia of 11mm. which looks to be pretty parallel
Can anyone help me locate a Collet nut for...
Hi Terry
Do you happen to have the Full parameter list for the Clone HY02D223B Inverter.
Unbeknown to me, until now that is,
I have been landed with a Chinese 'clone' version of the HY02D223B...
Clone HY02D223B
Unbeknown to me, until now that is,
I have been landed with a Chinese 'clone' version of the HY02D223B VFD
It is evidently clear that the parameter list differs from that of...
Unbeknown to me, until now that is,
I have been landed with a Chinese 'clone' version of the HY02D223B VFD
It is evidently clear that the parameter list differs from that of original version....
I have heard it said that if one moved an axis manually that there was a risk of damaging the controller connected to that axis.
Something about generating a voltage and feeding it back to the...
NOTE FOR Moderator, Would you please remove the previous posting of mine on this thread. Many thanks
I need a littler help please. Mr moderator, if this is in the wrong section would you please...
Hi, I dont know if you are still with this forum,
I also have a Haspa K24 spindle motot 24,000 rpm but I have trouble finding a Collet Nut, Can you help with the Size and thread please ?
Thanks
...
I have a Haspa K24 Spindle motor but I dont have any collets.
Can anyone help me locate them please.
I have managed to get my Spindle motor running again but it would be good if anyone can check my settings please. Here's what I have
Parameter Number followed by value set followed by descriptor...
I need a littler help please.
I screwed up my settings om my FR-D700 Mitsubishi Frequency drive.
I'm using a Chinese spindle motor 200730184245.5 rated at 8amps 400Hz 220V 2pole 24,000RPM,
Can...
Since posting , I've been an idiot. I had one of my jumpers incorrectly set. How I missed it I'll never know.
Thanks for your help it has been very much appreciated.
ESS + C11 now have movement.
I have a Warp 9 Smooth stepper connected to my C11 Multi Function Break Out board
I'm getting no motor movement when jogging with the keyboard. My setup is listed below and I need some help.
...
Thanks eriks, So it's similar. The one I have shown is 15Watt. Will the 10W version cut through 5mm Plywood. Do you have a manufacturers model or part number on your laser, where can I buy ?
So you are using your original 3 axis stepper? Do you have any build details for the Arduino? Connection diagram ec?
How is Focus achieved?
Is the Z axis utelised to control depth of cut?
Lots...
Hi Eriks,
Whats an Endurance laser ??
Thanks, I'm using a C11 multifunction board from CNC4pc.com which utilizes the parallel port, I would like some more info on adding the Arduino and software control.
Aha! learning starts, so what I proposed to use is a diode laser ??
What alternatives is there to enable me to engrave or cut 5mm Ply ??
I Ideally I wanted to use my existing control board, the electronics are already in place driving the steppers so why go and add an Arduino ?? Does your 2.5watt laser cut 5mm plywood ?
Thanks for...
I have been using my CNC 3 Axis Router successfully for several years, but now I want to experiment.
I currently run Mach3 with Aspire software and now want to try Laser engraving.
I do not want to...
Can anyone help me identify this wee lathe.
I'd be very grateful,
Thanks
George
Hi Russ,
I attempted to move my 'Rotary' tool changer through 360 degrees by using the following MDI command.
G0 A360
I finally got it to rotate through 360 degrees by changing the 'Steps per'...
Thanks Russ, command line moves are not consistent!! the travel of the rotational turret varies, I'm expecting to arrive at each tool position but sometime tools are skipped and the turret moves...
If I change that to an 'End' Russ the Macro won't compile ????
George
Thanks Russ,
XML and M6atart attached.
Summary:-
I'm having lots of trouble with my 8 Position Turret on my TCL160
I have searched the forums up and down in the hope of finding the correct...
Hi Russ,
An update on my Boxford TCL160
The spindle motor is now running in the correct rotation.
I measured the output Voltage from the BOB and Max 5Vdc was obtained at a spindle speed of...
Hi Russ,
Do you have the settings for Mach3,
I'm looking at Engine Config Ports and Pins - Spindle Setup but I'm still confused.
Ports & Pins output signal are by default
Output #1 enabled...
Thanks Russ,
I'm using Mach3, is there an upgrade cost option upgrade for Mach4 ?
Things are slowly coming together here.
As I said earlier I resurrected my Boxford TCL160 lathe which I shelved...
Great,
Many thanks Russ.
Thanks Russ,
Yep my Break out board (CM106) can be set to either 5v or 10v output so no issue there, thanks for the heads up.
I'm using Mach3 Turn for control software so I can set the...
Thanks Bevins,
I think you mean pins 5 & 2 not pinw, am I correct.
Would I be correct in saying that the 'Start forward rotation' is taken from one of the relay ports on the CM106 BOB
Thanks
...