use the pocket feture not frame if avalable
Type: Posts; User: wcopley
use the pocket feture not frame if avalable
ours is the same way I do not think you can it was purchased with either type 1 or 2 from what I read
Bill
Thanks for your input. I am sure glad you would not hire someone like me. I have been doing what he was asking and can proove that but saying this is what I want and not offering any type of info on...
A lot of info on requirements. How about benifits
Bill
It appears it may be looking for the floppy drive first. when you hit escape it will bring up dive menus. this can be changed in dos in your networking but I don't recall how at the moment.
Bill
John and Mike
Thanks for the help just alittle editing and it was up and running
thanks again
Bill:cheers:
as stated 4" facemill 0 depth of cutblank is burn out just about 3/4 inch wider and longer than what you see
Thanks Bill
If someone could help I need the g code for the profile cut on the outside using a 4inch face mill just a z zero cut 1 time around starting at the top left Mits 520m control
Thanks in advace...
Not sure about lathes but om our mills we only need 1 end after all the lines
Bill
try here for free http://technology.calumet.purdue.edu/met/mfet/275/toc.htm
Bill
we have a VM30XP Cent7 control and had this happen It was being caused by a external keyboard. I found out by accident no one had a clue and it was brand new.
Bill
I use it all the time for 2.5D work and communicteing with our mitsubishi control
Bill
check your way lube ours beep when low
Bill
sounds like its variable speed No gear box
Bill
Rogdog
email sent let me know if you receive it
Bill
http://www.meau.com/eprise/main/sites/public/DOWNLOADS/-search_results?SType=3&DocType=010&SessionNum=&UserID=&Division=00010&Opt1=Yes&submit1=Search&Family=0001010005&Series=000101000510060&Line=&Man...
http://www.meau.com/eprise/main/sites/public/DOWNLOADS/-search_results?SType=3&DocType=010&SessionNum=&UserID=&Division=00010&Opt1=Yes&submit1=Search&Family=0001010005&Series=000101000510060&Line=&Man...
http://www.saftronics.com/PRODUCTS/ACDRIVES/LEGACY/PC3/X020127%20-%20PC3%20Pocket%20Programming%20Guide.pdf
check this link
EF3 External fault input
external fault input function terminal
dont know if that will help
Bill
what control
Probably m41 low gear
m42 high gear
Cant be of much help on that model we have a RW20 and a VM30XP
I can tell you that we have had great support from our dealer and Milltronics
Bill
What model ? we have the centurion 7 control I like them
Bill
I run 2 milltronics cent 6 and you can set g54 g55 etc z offsetes just like fanuc and other controls (go to cordinate work choose cord set z value enter key)
simple
Bill
Does anyone have any opions on these or any opion on support in NW Pa.
We are looking at getting one
Thanks
Bill
Should it not be M98 P=sub prog # L4= # of repetitions
m99 Cancels and send back to main program
Bill
Im not sure if youre using carbide or not high speed use aprox 40sfm
carb 60 sfm aprox
Bill
Oh Sh**t may be inconel or some other nickle based material slow down rpm and feed rpm is way to fast
Bill
2 flute endmill WD or kerosene feed is way to slow try 2o ipm you have to get the cips out of the way take it all in 1 cut
Bill
I was a high school drop out that was along time ago. Now i program s/u and operate our VMC area. And have my own part time business. I would say if he is willing to learn your already one step...