Can this controller be used with a plotter?
What program to use to prepare the control program? We need an offset calculation for a vane knife, and we need a rotation of the creasing roller.
Type: Posts; User: Anriro
Can this controller be used with a plotter?
What program to use to prepare the control program? We need an offset calculation for a vane knife, and we need a rotation of the creasing roller.
doesn't work well
1) the laser turns on too early, before reaching the starting point. because of this, it burns everything in its path
2) nothing is visible on the preview
3) you need to press...
and thank you for the quick feedback
When manually moving from the keyboard, the machine began to stop abruptly, although the deceleration cost is 200. This happened after updating the firmware and software.
This happens when moving...
It would be nice if you made it a commercial product with an adequate price.
Actually, 99% of mach3 interface board fits your board. In it, you just need to swap P1-P14.
It can be seen that you...
Explain where such wild prices come from?
How can such crap with 3 connectors cost 22 euros? https://planet-cnc.com/product/adapter-for-10-pin-header/
Is someone buying this?
I can give free...
I set the acceleration to 2000 and it still slows down. In these places, there cannot be such large accelerations, the trojectory is very smooth. It's not about acceleration.
This happens very...
Nothing has changed. The machine works in jerks, and only at two points. You can watch the simulator yourself.
Why does the machine jerk up and down?
https://www.youtube.com/watch?v=aRmi5EaEBcU
where is it set?
Yes, if you increase the speed limit it will work fine. But even if the z-axis is stationary, the machine will still twitch, this is wrong. I don’t know how the program algorithm works, but it’s...
The speed along the z axis is much lower than the limiting speed. I do not see the logic in such a limited.
Why does the machine work jerky? Before each line of the program there is such a jerk.
TNG 2020.02.12
https://www.youtube.com/watch?v=eznQxjGrXoc
so with a stop at the M3 command do ??? or make a normal laser postprocessor.
I did not change anything, all the default settings. where to see this script?
why does the speed of movement drop on command M3? the machine moves jerkily.
found half a day later. as if specially transferred to another place so that they would suffer. :D
How to make the screen refresh more often ??? I change the "refresh rate", only numbers are accelerated, and the main screen doesn’t change. Why even make such slow-down default settings?
For example, I press a button on the keyboard + turn the wheel on the mouse and the axis moves. Can I do this? Mouse wheel acts as an encoder
How can I adjust the mouse wheel to move along the axes?
Because when I asked, thought it was difficult. And then I tried it and it turned out easy. True, I'm not sure that it will work correctly in 100% of cases.
In addition, you have written that MK3...
I did it myself, it takes even less than 5 minutes. I don’t understand what difficulties you had.
Can you do it in artcam? this is done in 5 minutes.
When will he be ready? I did not find it in the new version of TNG.
Win7 work? Support ended yesterday.
This is clear. But in the control program, the spindle turns on at the beginning, and turns off at the end of the whole program !!! But it is necessary that he turn on only when the laser approaches...
Can I make a postprocessor for laser cutting in ArtCam, or Vectrics? What would the laser (which is connected to the PWM output of the spindle) be switched off at the time of transition?
I can not...
Why move somewhere if everything is working so well?! Just Bill Gates is too greedy :D
This is very very bad. Nothing can be done about it?
Why TNG program is not installed on Win32 ? win XP