This 30 year old cylinder has molded seals that we did not even try to replace. We added a once of brake fluid to swell the seals and stopped the leak. Been good for two years so far.
Type: Posts; User: tahlinc
This 30 year old cylinder has molded seals that we did not even try to replace. We added a once of brake fluid to swell the seals and stopped the leak. Been good for two years so far.
Solution: Replaced Z-axis drive. All is well.
How do we identify the transistor module?
The drive shows 8.
Daewoo 300 Puma Lathe Fanuc 21T has 449 Z-axis INV IPM alarm in winter only. Works fine during the summer. In winter machine must be on for an hour in order to clear alarm. Anybody had this happen to...
a57l 0001 0037 | eBay
There should be a plastic line that comes down from the top left of the head stock to a fitting on the side of the cylinder.
RAM Parity Error can occur when batteries are low and some of the memory gets corrupted. Check the voltage of the batteries on the door. Remember, you loose every thing when batteries are removed...
We found this problem caused by bad FANUC Magnetic Sensor Amplifier shown.
Used ones are hard to find. New ones as more than $1000. Almost impossible to repair. Usually found inside the headstock....
Experienced Fanuc repair fellow needed.
We have a 1987 Monarch C10 Slant bed with Ge Fanuc 10T that needs work on control. Located in Tucson AZ.
Please cal 520-403-9002
Jim
This worked!
(call with M66 P320 = 66)
%
:9001(TOOL FETCH)
#1=#4120
#2=#4003
G00
G40G49
Thanks!
How are you calling 9000 and setting #149 global variable?
Did you get an answer?
Jim
My 6M has Macro B. I a looking for documentation on how to use it. My Smid book talks about "O" and later controls.
Jim
Cylinder is not pushing drawbar far enough release pull stud.
Construction of cylinder reveals that it is an air oil force multiplier. Perhaps oil is low so it does not develop full travel.
Any...
Thanks
Hi,
I am looking for info on how to search for a specific parameter number, instead of paging with the arrow keys, on a Fanuc 10.
Must be very obvious to all because no info on web.
Thanks,...
I second that!
110 Ft-Lbs seems pretty high. Folks typically only tighten vise enough to resist the cutting forces. You would like the vise to move in the event of a crash.
Procedure to square vise:
Eyeball...
Hi,
I just installed Scomm on XP and had no incidents. The program is nicely laid out. I am interested in incorporating comm into my Autocad abased cam program at the source code level.
If that...
I do not have that board.
Sorry.
I will check tomorrow.
Thanks
The sensor is for a Kitamura Fanuc OMC.
Jim
520-403-9002
We have the sensor but need the preamp!
Jim
Step import to ACIS solids (AutoCAD) from Parasolid yields a solid model that will have a 2D representation of holes as two arcs in order to show a circle.
This AutoLISP routine will remove the...
You batteries should last several years.
Another help is to Tap on the side of the chuck at the same time.
Jim
Sue Scott [email protected] has her husband's Letterease Autocad plugin.
Expensive but good.
http://www.softscout.com/software/Engineering/Computer-Aided-Design-CAD/Letterease.html
...
Ben,
Your 7.5 HP Interact CNC will need a minimum of a 10 HP PH converter to operate correctly. Bigger if you can afford it.
Jim
Excellent DNC that does drip feed.
CodeShark lite $20
http://www.softsquad.com/products.htm
Cat 5 network cable makes good hardware handshake.
Look at offerings:...