I have a Cincinnati Sabre 500 vmc equipped with Acramatic/Vickers 2100 control. I am getting following error while booting. I have checked 24VDC power supply OK and CMHD I/O card healthy LED ON...
Type: Posts; User: rai
I have a Cincinnati Sabre 500 vmc equipped with Acramatic/Vickers 2100 control. I am getting following error while booting. I have checked 24VDC power supply OK and CMHD I/O card healthy LED ON...
I am looking for a Electrical wiring diagram of Topper TNL - 100T equipped with Fanuc OTC and S series Servo / Spindle drives.
Kindly someone send me its electrical diagram.
I shall be thankful to...
Somebody help me please for ycm-vmc-65a parameters and ladder backup.
[email protected]
I am looking for a parameters and ladder backup of Supermax YCM-VMC-65A equipped with Fanuc OM.
As it's ladder EPROMS got damaged.
Please help me to get the same.
[email protected]
I have a Mitsiubishi M64S and an error P462 DNC ERROR - L01 DNC ERROR-20
Kindly somebody help me, as i am not familiar with Mitsubishi system.,
Sir,
In my case 926 FSSB alarm comes as spindle load increase.
without load no problem.
I hv checked optical cables, 24DC SMPS, etc but no sucess.
Is it possible due to linear scales too?
As...
somebody help me
I have a Miyano BNC34C2 equipped with Fanuc 0 Mate TC & turret driven by a GE Fanuc Versa Motion servo motor.
Right now it's turret is not working, As I am trying to Home it's turret, it is keep...
PLC program should be on eprom.
And parameters i will send you.
[email protected]
How do i get PROGRAM CLR state by pressing reset button?
I have changed Parameter #3402 bit #6 =1, but not effective.
I want to CLR program buffer while pressing reset button in auto mode.
It is...
I am looking for manuals for Cincinnati 6R, OD, 24" whl, full auto cycle, BTW auto wheel dress.
I shall be thankful to you
Please somebody send me it's parameters.
kindly someone help me,
I have a Nakamura Tome TMC-18 equipped with Fanuc 21T,
I have lost it's all parameters & ladder as well, As it's mother board got damaged.
I would much appreciate, if somebody help me & provide me...
I have a VMC equipped with Mitsubishi M64S cnc controller.
I want to change it's axis over travel stroke limits.
I do not know that how do i change it's parameters?
As I am not familiar with...
I have a EUMECH MC800P equipped with Fanuc OM C & Alpha servo & spindle.
I need it's parameters, Diag. parameters & ATC Macro.
Kindly help me somebody.
[email protected]
I have a cincinnati Sabre 750 VMC equipped with Fanuc 0M.
Kindly somebody arrange to provide me it's complete parameters.
[email protected]
Problem resolved, as Mori Seiki M022 card was faulty.
Now machine is in working order after repair of M022 card.
Mori Seiki MV40 equipped with Fanuc OM-C 30 TOOL ATC
It was working perfectly yesterday, today as i started this machine, it's op stop & Auto power off LED lits.
I have checked Optional stop &...
I have a Fanuc tape cut W1, as it's axis are working except sparking.
I have checked VCC card fuses, Discharge power circuit fuses, but could not find any faulty part.
As I am not familier with...
I am facing same problem. Have your problem got eliminated?
Is it possible to get it's macro program?
[email protected]
Kindly send me too procedure for zero return of the turret on the goodway machines.
[email protected]
What are the Tool Nose compensation parameters to be set in fanuc Oi Mate TD?
I have a Takisawa Mac V0 drill tap centre equipped with Fanuc OM-C tool magazine motor equipped with NSK SERVO megatorq drive.
Right now it's magazine is not working, I went thru it's ladder and...
I have a Wasino model LG60 equipped with Fanuc OT-A with dc servo & dc spindle motor fuji make.
It's axis are moving but it's spindle is not working.
I would like to replace it's spindle drive with...
I have a Miyano BNC12S equipped with FANUC OT-A
Presently I am facing couple of problems like chuck, spindle, auto mode are not working, even machine ready signal led is not getting on.
As it is...
kindly do send me it's pdf
[email protected]
I have a Fanuc drill tap center equipped with Fanuc OM-C & I/O card is C6 but having different connectors like M111, M112, M113, M114 & M115 with ribbon cable type as would like to edit it's ladder....