Search:

Hi Dhawal,

Check the ground wire connections. sometimes if the whole circuit is not grounded properly or if any wire of the motors is not connected to ground on the break out board etc. The...

hi,

Were you able to solve this?
im using nc studio. my spindle runs for a few secs (5-10) and stops, during that my PC freezes and then i get notification about limit switch on.

Hi,

I am getting an issue with the fuling parameter. how and where did you find which parameter was for what?
Were you able to solve the problem?

Hi Jer,

I have the latest one too. These boards always work, the error is mostly with the software settings and later with steps sometimes. If the motor locks that means u r doing it right. Play...

So i helping a friend revive his Chinese CNC router 1313B (unused since 3-4 years). I need help identifying the Spindle VFD and limits + emergency stops (coz i could not find any)
They only need...

Hi Geof,

Was just wondering if spray painting MDF in oil based color will help in waterproofing the MDF. also, would a base coat be required for the same. Any idea on this one?? Thanks !!

Hi,

I have emailed you.
reply to me back at [email protected].

raj shinai

thank you, had set the pins using the schematic...but your screenshots helped me confirm them.


Now, it is time to order the belts! n calculate the ipm n ill be ready for world...

Am really glad you replied...was finding it difficult to come up with a solution by myself...really helped.
Im using wires to connect the board to my driver..not tested them yet though.
And, wow...

hey mr. james,
Checked the cost of the pcbs with the shipping and the customs charges, here in mumbai..totally, it makes it a lil expensive for me to ship it to india.

so guess, for a while im...

hey,
iv built d linistepper...
if u still around, could u please send me a pic of your entire circuit with break out board n drivers connected together with the psu.

Kinda stuck at that part..

actually im really the plug and play type fellow when it comes to electronics..
and this open source options is taking my nights away..

Im in india, do you deliver linisteppers here?

also im...

thank you for the support mr. james,
I should have done my homework (reading the page) properly before asking you about it...
yeah, im just trying to make a controller by myself..so the questions.

guys,
iv built a 2*4 mdf cnc, im going to use belts to run its x and y axis.
could you help me with what kind of gear should i use for it.?

and will a 9mm belt (wid steel wires) be sufficient?...

hey ian,
Im interested in buying the 6560...since iv just built a small mdf machine to check if i coudl build one and if i could buy all the parts locally.
im in india, so the price of building...

Hey mr. james,
The PSU iv got has got only 2 wires...its 12v, 1amp.
how can i connect it to the 6 pin power?

also the mab6h connectors used in the linistepper variant, what are they connected...

yup thanks..

Could you also tell me what be the effect if i run a stepper motor rated 2 amps on 1.5amps?
- would it affect the torque or speed or both?

From which seller did u order the board? and the drivers?
What was the total cost of shipment to india?
more importantly, did it work properly?

im ordering one to mumbai, in a few days...(if my...

hey thanks for the link..
have not been through the page yet, so hope it solves all my queries.

Also, y use a 6 pin socket to supply power to this board? i thought power was all about +,- &...

How do i calculate the resistors required (R1A,R1B,R1C,R2A,R2B & R2C) on the stepper circuit?
and Why are they needed to be calculated?

Wow tht was a real quick reply from you bro...

Guess i should be spending more time checking my mails than doing other stuff now..but its just like that in my time zone.

Neways, jus trying to...

I know its a very late for me to reply on this thread...but i can help u with sourcing servo motors, controllers n other parts (new and refurbished)...
Been purchsing a lot of these things from...