Search:

Thank you for the help, much appreciated.

My dealer is saying those part numbers do not come up in their system.

Hi, I just purchased a 2005 Lynx 220A and of course it did not come with manuals. It has a Fanuc Control but I am not sure which one, it says Fanuc i series, looks the same as every Lynx I've seen in...

Just for anyone's info, electrostatic SUCKS! Don't buy into that crap. They are a maintenance nightmare.

I am looking to purchase a cad/cam program and have gone through the SW/SC demo, but I want to know what the people that have it think about it. I have Fadal VMCs and I design/program my own products.

Well I've decided to try these, Trion Industrial Mist Collectors: Top Rated Oil Mist Collector and Eliminator Designed for Today's Modern Machine Tools

They're making me a killer deal on 2 cheaper...

AWESOME!! Thanks!!

I've been turning the coolant off when it comes to face mills. I run all 1/2" and smaller endmills and of course drills, so drill chucks create a lot of mist. Can't set coolant nozzles to hit end...

I have 2 Fadals in my shop, all I run is Aluminum so spindles are running high RPM all the time. This of course causes A LOT of mist, which gets on the belts, eventually causes the belts to get so...

If you have it, I'm interested.

I don't care one bit about gibbs, crap program as far as I'm concerned. I would like to get them both on NT or whatever newer than 95.
What would it take to change CPU and upgrade op? Even if I...

I have a 2000 Fadal with a 32MP control and I just bought a 93 Fadal with a 32 MP control. The 2000 has windows 95 which sux and Fadal wants $3k to upgrade, now my 93 is going to be even worse. My...

Nothing? No one has this control? No Info?

Ok, I've searched in here and the net and fnd very little info on the 32MP hard drive, but mine is toast. I haven't called service yet cause I'm not ready for that bangin, is there an affordable way...

I need a dedicated engraver, must be capable of 3D engraving. Not difficult shapes but definitely not 2D. Any suggestions would be greatly appreciated.

I have an OLD 325, 89-90 range. Awesome machine! For the $$ can't be beat.

I had this happen the other day, I rolled the Y off the switch and it still wouldn't fire up. Reach down there and manually trip the Y limit switch a couple times, it was sticking. Give it a try if...

When I was on the phone to service, they said all axis were the same. I bought an extra set of bearings and seals to be safe.

Thanks for the link, saved that one. Which one did you install and how difficult?
When you age again, check it out, we're travelling all over the country having a good time with it.

smittys800, what is the LCD upgrade?
It took my son and I about 2 hours last night to do the thrust bearings, I bypassed the coolant on the x, when they y goes bad I'll do the same.

You should...

Thanks for all your help.
We make hop-up for 1/5 scale Rc. They're huge, they have 2-stroke motors and burn gas instead of nitro. Real kick and it's growing expondetially.
Check out our web-site,...

One more question, obviously the ball screw will turn during this process and the motor might turn, will any of this matter? DO i have to worry about any indexing?
I really appreciate your help.
I...

Thanks, that helps a lot.
Would anyone know the actual bearing number? It looks like SKS bearing, I might be able to get it from a local source today instead of waiting for fadal.

Could someone please tell me where to get directions for changing the thrust bearings? I know mine are bad, but where are they even located?

Hi,
I have a 22 16 Fadal, if I push/pull on the table and I get .007 movement. I get this on the end of the ballscrew too.
Is there anywhere I can find directions on how to replace the thrust...

I would like to know if any of you had spindle Failures with your Fadals? We have a Fadal 40x20 that is one & half years old & gone through 2 spindles. This machine only runs about 40-50 hours a...

That's interesting, I didn't know that. Are there any advantages other than being able to DNC? How hard was it to change? And if you would, what was the price approximatley?
Dave

Thanks dogstar, I got a post processor to work, a little editing & it works great. Where did you get you dyna 20 that you upgraded to? I've been thinking of doing this as I have some rather large...

I am having a problem with my coolant pump, it starts out pumping fine & continually dies off. I pulled the pump & there's 2 rubber wasers just floating on the shaft, coolant sprays out of the top of...

Is that his member name here? I looked through the member section & didn't see that name.