Nå er den solgt
Type: Posts; User: rogerer
Nå er den solgt
Kraftig cnc-router prosjekt
Fortsatt til salgs, den ble ikke solgt allikevel. Åpen for bud!
Fresen er solgt!
Roger
Selger prosjektet mitt pga barn...
Her er all info:
Kraftig cnc-router prosjekt - Side 4
Got it sorted, thanks!
Had some problems with the tool change stuff, so I just deleted everything about that stuff. Now it actually works! I should do some testing before raising the flag.
Thanks for all replies, been on holidays i the meantime.
I have managed to make a postprocessor that is one big step in the right direction. Still I see some problems that I can't find the...
I really don't know, Edgecam has written it for me. It is a simple program to make some circular pockets.
Can I make Edgecam to forget about all the tool change stuff an put out a simple g-code?
Thanks! the version is 11.5
It is a gantry router. X moves the gantry, Y is along the gantry and Z is up and down.
It has a milling spindle attached to the Z axis. There is no rotational axis.
Attached is a g-code that...
I am using EMC2 on my 3 axis mill. Does anyone have a postprocessor for Edgecam that works with EMC2?
EMC2 can't read the g-codes that edgecam produces.
I am using EMC2 on my 3 axis mill. Does anyone have a postprocessor for Edgecam that works with emc2?
Got it!
the PD000 was set to 1, so I could not change any values. When it was set to 0, I changed the PD001 to 0 and it all worked. stooopid!
Thanks!
Hei
Da har jeg fått testa oppsettet:
YouTube - testingspindle
Legg merke til lydnivået. Det meste av støyen er viftesus fra VFD'en.
Dette er altså en Huanyang VFD med 1,5kW vannkjølt...
Hehe, nå ble jeg fornærmet :) Synes forsåvidt oppsettet forøvrig er ganske kraftig også. Vi får se når vi får startet opp med fresing.
Jeg er ikke akkurat modellflyentusiast, men det var vel den...
As the title says, my Huanyang VFD says "r00.00" in the display. It will not start the spindle.
It worked fine when I first tried it out of the box (but I did not have a spindle connected) the fan...
Da kom det litt snacks i posten :)
Hvilken kvalitet/overflate er det på rundstålet?
Jeg også vil se video! Alltid morsomt å se et nybygg i bevegelse
Har ikke tenkt så mye på hva slags utstyr jeg skal bruke. Ser en del andre bruker pumper ment til akvarium. Blir vel noe i den duren, er ikke store strømningen av vann for å kjøle ned tipper jeg. Er...
Jepp jeg har kjøpt en sånn fresemotor. Den ligger i tollen, jeg får melde tilbake med rapport når den kommer på døra.
Hei
Tenkte å dele min byggeblogg med dere, se her:
http://forum.modellflynytt.no/showthread.php?t=23367
Design:
Firkant stålprofiler 50x50mm satt sammen av bolter i en slik formasjon at det...
Current set resistors - check
Step polarity - Where do I check this?
They are running with no load, "in air".
I run a Gecko G540 along with 4 steppers from Keling (KL23H2100-35-4B) driven by the latest version of EMC2. Power supply 48 volts.
At low speeds/feeds the motors tend to stand still. I also use a...
Running Keling steppers on a G540 drive and emc2 software.
When I run the feeds down low, the motors do not run at all sometimes. EMC2 say the motors are running but they don't. Is there a minimum...
I installed the version 2.3 and ran the same stepconf as described.
When running very low feeds, either one of the motors or both would not run at all. This came and went as I tested. Does anyone...
Ok, I now realize that the G540 is a static 10 microstepping drive.
:withstupi
Not worse than that? Thanks!
Hi
I have 4 motors, a Geckodrive G540 and running Emc2.
How do I get 2 of the motors running the x-axis simultaniously?