I run a large batch of parts every year that are turned on a lathe and milled/drilled complete using the C-axis. We hold the part in a pie jaw because when the part is is milled it springs when...
Type: Posts; User: DerekSSS
I run a large batch of parts every year that are turned on a lathe and milled/drilled complete using the C-axis. We hold the part in a pie jaw because when the part is is milled it springs when...
I am looking for split clamping ID tool blocks for a 24 station hyrbid on a ST30-SS.
I want to chuck on a carbide dampened silent boring bar...and they say you shoudnt screw into it.
Anyone...
I have a pretty complicated vacume head to make and it is mostly made of Teflon.
I am wondering what speeds and feeds to run...150SFM? .001-.004 feed?
I have a sharp 30 degree diamond style...
The 90 deg live tooling like you posted isn't plug and play like it should be..basically i would shim it either direction and measure for center just do some test holes.
But to get a true dead on...
You may have too many codes going which it's reading and slowing it down.. here is some sample code from a part I am running.
Another trick is to just enter into the mem screen
M154
G0 C0. to...
I have done quite a bit of threading on our machine using a threading tool.
But my boss wants me to use a tap to do a M16x2, and I can't figure out the best way to hold the tap. I've done lot's...
It is square bar so I want to run as fast of rpm as possible over the rough portion to save cutters.
But doing to math at .875 with 200 SF/pm thats only around 1200 RPM through the rough.
We have a 3" opening in our drawtube and we are going to have to line a piece of 7/8 square.
I looked a trustycook.com for a custom liner but it was nearly 400$
I am only going to be running...
Setting 7 parameter lock to off...gotta have e-stop pressed..
We have a Haas ST30-SS with the 24 station turret and we use the factory holders. The OD turning holders when placed on have almost no slop at all but our ID toolholders have alot of slop to them.
...
Ron,
I finished the groove and everything is fine but I had to do some sanding to get my corners smooth enough.
The piece is 6.625 OD and was turned down to 4.850...the groove width was 2.469....
Hello,
I am making a groove that is close to an inch deep on a side in 304 SS material and I am using a groover that is 1.25 long. I am using a feed of .002 with a SF/M of 200 which usually works...
We have a Haas St30 with the auto probe.
When you touch off a drill you have to put the highest point of the side of the drill over the probe scensor and then go into .001 mode.
Then you hold...
I went through and eval with OneCNC and my tech guy said spiral toolpath was supported by there mill version but not there lathe.
And I asked him about setting an inner and outer boundary for a...
I have looked at Mastercam, OneCNC, Gibbscam, and Partmaker.
Are there any others I am missing that are priced well and powerful?
The cutting I am doing is mostly C-axis turns with no...
Does anyone know of a place I could find schematics of the Haas machines? The books they come with are not very in depth.
Also is there a place where i could find info about threading such as the...
I figured out how to control the g76 manually...go to setting 99 and make it what you want your first pass to be...make you D. value match that.
And make setting 86 what you want your final pass...
Could you give me a g76 program example that you have done? I know the machine shouldnt be making 20 passes to cut my thread I'm only going .078 deep and have .009 as my first pass.
Ideally I...
The thread I am making is a 3/8 ISO 228 Witworth it's some crazy british thread.
I am getting a 55 deg insert so I shouldnt have to do anything special. Do you ever use the IPS g76 cycle or do you...
After I make my last pass with the threading tool I re-run my profiling op over the lead in and thread to clean it up.
What do you mean by profiling op? And with a .005 DOC wouldn't that...
When threading it says not to use constant surface speed. I usually run about 255 RPM. My threads turn out usable and work fine but aren't as pretty as some I see.
What is the secret to getting...