Problem solved
I created a copy of an earlier Profile in Mach3 and deleted the corrupted Profile.
That did the trick.
Jerry
Type: Posts; User: jerrywi
Problem solved
I created a copy of an earlier Profile in Mach3 and deleted the corrupted Profile.
That did the trick.
Jerry
Morning
I've completed my hobby cnc build and while calibrating the nema 23 motors for steps/inch the "x" axis crashed at the end of it's travel. I reset mach 3 and continue the calibrations and...
Fastest1, Gerry
Thanks for your input
Jerry
Hello group;
I just completed wiring a solid state relay to turn my rigid router off/on through the G-code. I’m impressed with its operation. I can now, not worry as much about being attentive...
Thanks for the info. this is what I was looking for.
Jerry
Good Morning Group and (Jim, cb_designer,JKountz,Crazydianmond and Mac)
I'm still trying to figure out what is going on with my CNC cutting Hieroglyphics.
What I've done so far is:
check my...
WOW! Jim,
I just turned my computer on to ask the group about a problem that just occurred with me and noticed your post. I have, what sounds like the same problem.
I've been using my momus for...
Hello Ian,
Thanks for the input. They seem to be the least expensive, However we all know you get what you pay for.
The search continues.
Jerry
Hay Mac and Andrew,
Thanks for the response. I also have a small four jaw chuck, shafts of various sizes and bearings. I had thoughts on building a temp. platform out of MDF before advancing to...
Happy Thanks giving Group,
Well, it's getting closer to Christmas and looking to fulfill my wish list.
I've decided to try my hand at 4th axis milling.
I've been using my earlier version of...
Hay Doug and Mac;
Thanks again for your inputs. Great video. I will start experimenting on some test programs and let you all know how it comes out.
Have a great day and I'll be talking to you...
Hi Mac,
Been away from the computer for a few days.
Thanks for your input.
My shop is sort of small and don't think I can fit a 6 or 8 foot table bed. I think I will try to master the technique of...
Hello group;
I have been using my Momus build (pre-version 2.0) for several years now, however I have never used the pass through feature. I'm not sure how I would index my work piece or set up...
Thanks Gerry
I appreciate your help
Jerry
Good Morning Nick and Gerry
I actually played around with this problem and the problem is two fold.
The Rings would be in the file when loaded into mach3 prior to the conversion to cncwrapper....
Good Morning Group'
I recently purchased the cncwrapper program and having problems.
When I use the sample programs it appears to work fine on mach3 however when I design something and load it...
I bought spray paint from Home Depot and it worked just fine.
I looked high and low for an inexpensive two part resin and believe it or not, I found a 32 oz. kit at Menards for $17.95.
It's from...
Thank you all
a lot of good suggestions
jerrywi
Good Morning Group,
My Momus project is complete, minus the top(ver 1.2) decided to try to adapt ver 2.0's top to it.
My question is I'm looking at purchasing a relay for my G540 that will turn my...
Looks great Bob
Thanks Chris, it was helpful
Hello group,
Just got home from work and notice this latest post. I was going to post a issue I have later when I had more time but will put this out there for tonight. If you all remember I...
Thanks for responding Royce, I placed my order for the Gecko G540 controller/driver along with the EZ-G540 DB9 Plugs.
Should have them with in the week.
Thanks all for your input
Jerry
WOW, question asked and answered. I was blind sided by the prices of the TB6560 controllers/drivers.
You pay a little more and you get better quality, support, documentation and less head aches.
My...
Hi again John:
Doing more research on drivers and WOW, there is a ton of dealers selling drivers with the TB6560 chip at very low prices.
I know you said too many people have problems with them....
Hello John:
I purchased the Rockcliff v10 cnc kit because it was all in one board. very simple install.
However after talking with the tech dept (very helpful and willing to work with me) they...
Hello group,
I too am having the same problem replacing my driver. my first was from Rockcliff and was very user friendly. I've been on a different thread and talking about the Gecko G540 and they...
Great Info Group
I did not know about the EZ-G540, so with a set of these I don't have to wire my own resisters?
I will order the Gecko G540, the EZ-G540 and some cable wire.
Once again this...
Hello Group:
The dealer I believe is Hubbard CNC Inc.
Thanks Group for your input on the Gecko G540 driver.
I've been looking at a lot of dealers selling the G540 and found one on E-bay (new). he states that he is offering the G540 with complete motor...