does this machine have a Micon8 PC controller on the back of the machine? If so then the timer is done by settings in the Micon8. Please let me know if this is the case.
Type: Posts; User: CyberCNC
does this machine have a Micon8 PC controller on the back of the machine? If so then the timer is done by settings in the Micon8. Please let me know if this is the case.
Hold the tailstock retract button for 30 seconds once power is up. There is an interlock that will only reset after the software latch is latched by holding in the retract button, or commanding tail...
Attached, please see list of Micon 8 data with alarms. There are two list of alarms depending on what prom version is on the Micon 8 board. You can always contact me direct at [email protected]
Does this machine have a Micon8 PC controller on the panel by the ATC, and did you check those parameters? Also if it has a Micon8 it will have alarm listed there also.
John, Please check your email as I sent you the information on where the machine was originally installed.
Dear Sir,
I do not believe this is an Hitachi Seiki machine tool. can you please supply Model and serial number if you are still looking for support.
Attached, please find procedure for adjusting the position of the ATC Magazine on a Hitachi Seiki HS630 with JuspointIII drive.
There are several types of alarms. They can be control related, or machine related. Please let me know what the alarms are so that I can point you in the correct direction.
Just because the switch is set to "0" on the scale does not mean that it is working. Please check the diagnostics for the switch "X0B6" on the diagnostic screen while the spindle is running. It...
There are two ways to clear your situation. The first is to make commands in "maintenance mode", but hold in on the spindle stop button while you depress cycle start button (this is an override) be...
What drawing are you looking for on the VS50? I do have some drawings available.
The most difficult part of the job is removing the old membranes and the glue they are held on with. We recommend using rubbing alcohol to clean the residue from the plate after removing the old...
You need to use ATA Flash Card, see attached procedure....
Hi, I have attached the Hitachi Seiki Procedure for back-up of the SRAM on Sigma Controls. One procedure is for Sigma 10 and the other is for Sigma 16,18, and 21 controls.
Memory card can not be larger than 2 meg.
The lubrication pressure switch for the spindle lubrication is located on the top of the spindle head just in front of the tool un-clamp cylinder. It looks like a plastic dome and has a adjustment...
All machines built by Hitachi Seiki were 208vac. That machine requires a minimum of 22 KVA transformer for a VK45-2 machine.And the 4th axis on your machine is the spindle.
It is apparent that this machine was not sold in the Americas. I only have records from Hitachi Seiki of machines that where sold here. I do not know what control is on this machine, nor do I have a...
Serial Number should start with VK47_ _ _ The number is on a Tag usually says Model Number then Serial Number
If this machine has the "High Speed" spindle option the it will have two lubrication tanks on the back of the machine. The tank on the right is for the high speed spindle option. There is a pressure...
Please check the 100vac. from the T1 transformer in the center part of the electrical cabinet. If that is okay, then check the voltage at CB-3, CB-4, and CB-5 located in the left rear cabinet...
[QUOTE=getsideways;1759068]we are having problems with our hitachi ht23rIII lathe. it has the lambda 40l control. yaskawa reloaded software on rack but now something in the plc parameters are not...
Dwayne, Please try typing eight zero's (00000000) and press Input when you go to parameter screen. This should unlock all parameters.
1. CyberCNC has most manuals for machines sold in the America's
2. Melodies can be called via "M" code functions. I believe there are 5 melodies available and can be called at any time during the...
Please visit us on Facebook: Cyber CNC Machinery Sales, Inc. - Big Bend, WI - Professional Services | Facebook
;)
Hello. What is the serial number and control type on your CA23? We may have a PDF file for this manual.
Tara with Cyber CNC Machinery Sales
Thank you for your request, we have this manual in-stock and available for shipment today. Please contact me at 262-662-1100 or email [email protected] for a formal quotation.
Original-Used TF20...
CyberCNC Machinery Sales is pleased to invite you to see a sampling of our newest equipment line from SMTCL-USA. CyberCNC is located 15 minutes southwest of Milwaukee and 90 miles north of Chicago....
Hello, Marcial. I am glad that things are running smoothly on your end, unfortunately I only hear from people if they're having a bad day! But, of course, I'm always here to help :) What machines are...
We offer technical support and parts for Hitachi Seiki, as well as used and new machine tools. Please contact me with any requests you may have! 262-662-1100
Tara Markiewicz for Cyber CNC...