Search:

Yes that is the one. You can get directions from a Kb control manual. These are chines knock off copies of the KB controls and act some what like them. You can use the manual though.
Why would you...

Yep sounds like motor surging, your motor controller card needs to be adjusted. My G0704 did that also when I first got it. Search Hoss's thread he has something on adjusting the motor controller...

need a Clusing 7/8" x 36" x 8TPI/.125" pitch
PM me if have one or know where I can get one.

Hi Mate
Got one word for you 2hp 3ph 3450 rpm inverter rated with VFD.
No worries.
CH

Hi All
I don't have any thing to do with this machine but I thought it really cool. I enjoyed watching this and I want one. Merry Christmas to all.
CH...

your about a month late. I already have what I need. I want be buying form Misumiusa any more.
CH

Hi
I think the only difference in 6061-T6 and T6511 is that T6 is not stress relieved and T6511 is. They stretch it 1-3% to relieve stress after extrusion and heat treat, and before aging. T6511...

Hi All
I got the connectors. I installed them yesterday and ran a part on the machine. Not any problems at all. These connectors are nice for the price. I will be using the synthetic water coolant....

There is no shield from the motor just 4 wires. the shield runs the length of the cable and goes to the controller ground plane( single point ground).
CH

Hi
I guess I don't under stand your point Ray. The pins are larger than the motor wires. The size of the insulation around the pins is 100 times thicker than the insulation on the wires. I'm only...

Amazon.com: M14 IP68 Waterproof 4 Pins Electrical Cable Connector Plug Socket: Computers & Accessories
This is what I'm ordering. They look like they should do the job. Thank all
CH

Thanks All
I don't have a problem with hard wired steepers if that is you choice. How ever my mill will be in an enclosure very much like Hoss's enclosure and removing the steppers and cable will be...

Thanks, will look at these closer. What I have now is the molex (sp) white connecters that Automation Tech, sent when I got my steeper kit. They really are not good for this type of use. I had to...

Thanks but I have the 60mm 570oz motors on X and Y and the mic plugs aren't fluid proof. I may get one of the NEMA 34 end caps but man they are pricey, and the coolant will not be problem for the Z...

Hi All
I'm starting to think of maybe going to flood coolant. I'm looking for connecters for the steppers that are coolant proof. I found some water proof connecters but not sure they will stand up...

Hi All
I have ordered a few thinks from Misumi for my mill. Now I'll be doing an up grade to my lathe with some Igaging Absolute DRO's My old eyes aren't what they once was and numbers on the...

Darn sorry to here about this. What ever you do don't pound on them(jaws). That will bend or worse bake the scrolls in side then the chuck is screwed up for good. When was the last time the chuck...

Hi
You know, detailed pixs are worth 10,000 words. If you can take several detailed pictures and post here maybe someone can see what the problem is. Several members here have PDB's that works.
CH

Hi All
I have the fix in, and it is working right. I don't really care where or who made the card fact is the jumpers used on it are cheap worthless parts that doubt was made in America. A bad one...

Hi again.
I found the problem there was a bad jumper on the C10 BOB. the Jumper should be able to connect some pins together that defines the function to the pins and it was bad. So I soldered some...

Hi All
I think I found the problem the DIR+ and PUL+ are note getting through the BOB to the DIR+ PUL+ which are jumped together at the Drive plug.. I have the 5vdc used for the signal but it is not...

Hey thanks for the info on the ESS route. The pins don't really mater as long as you have them entered in the right order in Config pins and ports.screen. You can have 2&3 on the X axis or 8&9 as...

Dang, I must be having a CRS moment I just can't figure this out. Ever thing look like it is working but the steppers just don't move.
Thanks
CH

All ready done that. Today, any special way it should be done?
CH

Sorry that is not what I meant. The mill will not respond and after trying just about every thing I could think of I swaped out the DB25 pin cable that came with the computer I'm using. Yes it was...

Sorry that is not what I meant. The mill will not respond and after trying just about every thing I could think of I swaped out the DB25 pin cable that came with the computer I'm using. Yes it was...

I don't know just trying any thing>
CH

Hi All
I seem to remember reading that a Printer cable will not work with mach3 and that you need a CNC cable is this true. I can't get my CNC G704 to do anything. I can't jog it, it wont run the G...

Hi All
I need a source with the best prices. I looked on Fleebay but they seem to be short 18-24" drops. I have a couple projects that need longer pieces.
Thanks and happy machining
CH

Hi
Nice job. Now you can git rid of that little hobby mill and put this on a Tormach 1100 and really get some machining done. That is a nice trunnion fixture.
Happy Machining.
CH