Search:

The burny looks at the cut o2 switch to start learning. put it in teach mode and cut the part using the tracer. the burny will ask you to store after you turn the cut o2 off

Contact Advanced cutting systems

A lot depends on the age of the supergraph some were better than others. also the 1070 is obsolete I would call hypertherm with the serial numbers to make sure all the updates were done. It is...

Oh lord don't remind me of that. koike fired most of engineering after that fiasco.

couldn't you use the mist pump out for preheat and the flood pump for cutting? both have programmable dwells. or use one of the flood outputs for preheat and spindle down for cut oxygen and you are...

first time for everything. I've called everyone i can think of with old burny experiance and no one has heard of a blue switch. there are some switches on the communications board but they are inside...

That ladies and gentelman is a classic oxygen leak.

steel cutting requires 99.98% pure o2. any less and it goes to crap in a heart beat. See where the steel is blown and not oxidized. No brainer....

acetylene has a very close thermal coupeling height so the .5 inch cut height is out. way too high. you are at a disadvantage with a 6 hole cutting tip as the pre heat is not liniar around the tip....

They are back i business!!! Linatrol Profile Cutting, Shape Cutting, CNC, Optical Tracer, Controllers, Servo Drives

I also saw some on ebay out of california.

some days i'm so stupid i can't think .....try ce instead of shift

see below

service mode Pressing the burny bu key (you have found that) set parameters as desired. press 97 var store, ce key to confirm, press 98 reset/restart. It will not read the new values unless it is...

It's under the U in burny,

alen

Marv

cm-50 is heavy, full of friction and a bear to fix.

I don't think the torchmates dynamic range to control the table will be of any use to you. Plus you would have to retune the drives every time...

I reviewed the manual http://www.machsupport.com/docs/Mach3Mill_Install_Config.pdf
the only easy way would be to use coolant outputs one and two. both have delays.
you may have to trick the...

These are not in the order as you have listed just some thoughts from an old fart.

1. clamping material. Very thin aluminum doesn't want anything pushing or pulling on it.

2 Perfectly level...

C-cut works great with almost any type of controller. Designed for shipyard use I find it very difficult to find fault with it.

glad to help.

Laural miss. The curve in the highway! Ya'll take care.

Marv.

Cal has reopend wescan under linatrol. Linatrol Profile Cutting and Shape Cutting Solutions - CNC, Oxy/Fuel, Plasma, Optical Tracing. He's still getting his duck in a row with long lead times but the...

To make the servoed cutting oxygen regulator, we used a separate pilot regulator, and made a replacement "dome" top to replace the normal tee handled spring pressure part of the oxygen regulator. The...

Floppy To USB Upgrades - Replace your 3 1/2 drive with a USB floppy simulator

Yes it is

Standard RS232 cable or crosslink cable? cross linked pins 2>3... 3>2 ... 5-5
Which cable to use? Any finely braided at least 2sets twisted pair shielded
DNC32 Is good and has a...

Oh.. you still must have dnc software and a computer hooked to it. I've used that to port a new desktop to a short haul modem but the controller end still needs a DB9 after the modem. there is no way...

Also look at creep time. this is the time the machine will move at 25% of cut speed and should be used on thicker plate instead of prerce time and it creates a trough for the slag to go out of. It...

the plate pro was offered with the d-10 and the burney replicator?

The d-10 had many issues reguarding the controller. Including a modifaction to the control board adding some filter caps. There...

If I was there , And it was only on the front half of the machine I would suspect the Y encoder/motor cable as it may have rubbed trough in the nylatrac grounding out one of the encoder lines causing...

Jonathan

You have a rs232 to usb adaptor that emulates the the d-10/ d-6 /d-11 communications protocol?
Or are you replaceing the floppy in the d-10 with an adaptor? That patent is owned by IBM....

Those were some bad times for engineering back then. When the price war started they tried to do many things and unfortunitly most of them wrong.

After some shake up in engineering they got their...

Cal ...I assume.

The weight of the torch plus lifter assembly plays hell on thin gauge plate as it rolls over the cutting slats. sometimes enough to crimp the sheet leaving dimples all over it as...

KAR stands for Koike Aronson Ransom. It is the US division of Koike Sanso Koygo (Koike Oxygen Company) KSK

They did use a few japaneese contrived controllers in the early days. Not recieved well...

It was the way it was interfaced. It shouldn't have been interfaced at all!! LOL If you turned power off on the controler the accroloop would bleed off through the drive channles and caused...