That may be true, I just saw that there are wood/composite options on the calculator as well and went with it. It seemed to be the only calculator I saw that took tool deflection and spindle HP into...
Type: Posts; User: drxlcarfreak
That may be true, I just saw that there are wood/composite options on the calculator as well and went with it. It seemed to be the only calculator I saw that took tool deflection and spindle HP into...
Fair enough, that makes complete sense and kind of figured that, but wanted to ask. I had assumed that the weak link would be the skateboard bearings as I have crunched a couple before wracking the...
Hey guys,
I am running a FLA standard machine with the skateboard bearings, upgraded nema 34 servos and a 2.2kw spindle. I recently started using an actual decent end mill instead of ebay brand...
Fair enough. Sounds like one more ground to go then!
Yeah, I wasn't a fan of it being exposed so I wrapped most of it in electrical tape just so it wouldn't accidentally short into something. Is...
So I messed with it last night. I tried doing one item at a time to see what had an impact. I tried the EMI filter first and that immediately cleared up the spindle requiring a debounce to not trip...
When you say wired correctly, what do you mean exactly? Shielded cables, no disconnects to the case but emi shields instead, all grounds go to one spot, keep shields on wires inside case especially...
Good idea.... When I put mine in I didn't read about it anywhere and tried to mimic other cases that I had seen that apparently didn't have issues. I am actually beginning to wonder if my old nema23...
Fair enough. I will have to look into my spindle to see if the connector will come out easily enough to do that. I also need to find a wire gland that is actually metal inside, and hopefully...
Fair enough I ordered the input power filter that Mactec recommended, I will buy 30' of that shielded cable that you recommended, abandon the plug and run the wire directly to the VFD. I also plan to...
I saw that you said that this cable was a requirement for a 2.2kw spindle in another thread:...
What is a preferred layout? Are plugs not good to have? Are there other quick disconnect options?
Ok, so:
1. No ferrite rings
2. 30A EMI filter
3. Redo the VFD cable with shielded cable inside the cabinet.
4. Faraday cage separating the top half from the bottom half of the electronics?...
And a few more...
427516
427518
427520
427522
I was only saying a new VFD based on the assumption from another forum thread that this one is on its way out (https://www.forum.cncdrive.com/viewtopic.php?f=2&t=2092).
I have no input filter...
Yes, sorry I forget that not everyone knows what I have been going through and forget to mention everything. The machine was running fine for about 2 years, then all of a sudden I got a weird issue...
That's true, and I don't see these motors losing position at all with their strength and the speeds I have dropped them to.
True as well, unforunately, I need a version with the debounce option...
I thought I had the issue sorted out, and went to try again today and the bit dove right into my piece. I took the Z-axis apart to install a new anti-backlash nut, and noticed when tightening down...
I took the z axis off tonight to check it out, there were a couple loose nuts there. I tightened it all back up and it seems to be working like a champ now. I think the threads are slightly stripped...
I actually sprayed the acme screw with silicone last night and it seems to have fixed the issue, now when I power the machine off there is so little friction the z axis noticeably sinks into the...
Exactly my thoughts. Its almost as if I am gaining steps, not losing them though. Like the lead screw is falling through the nut at the top half of the Z travel. This happens only in the top half and...
It's not an issue with the motor for once on my machine! I upgraded to Clearpath servos and am utilizing the closed loop portion so the machine will shut off if the servo isn't behaving correctly.
...
Hmm, I can definitely say that I have never oiled it. I figured its some sort of plastic piece so it would need it. Its from here:...
I am having an intermittent issue with my Fineline machine. When I go to run a program it will start with the z all the way up to the safe Z height, and then drop to the piece. Randomly sometimes it...
So I received the bolt yesterday. Fast shipping, though shipping did cost 3 times the cost of the bolt! The machine is back up and running. I will say that the bolt I broke must have had a slightly...
My Ace did not have shoulder bolts, and actually didn't know what they are.
I just ordered a replacement from McMaster. Thanks guys!
I'll check Ace out today. Thanks for the suggestion!
That's a true thought. I myself have broken many a bolt when tightening them. It could have been the shock of hitting the 2x4 at speed made an...
A 2x4 just got in between my carriage and bumper stop on my new Nema 34 R&P and snapped.the pivot bolt before I was able to react and hit the E-stop button. I am trying to find a replacement to get...
Hmm, that could work for smaller pieces and be a lot firmer, but boy that would be a heavy mold for larger pieces! I really like the cheap vacuum bagging idea you mentioned. I may give that a try.
Ahh fair enough.
That is a lot of great info, I am going to have to look into a bunch more things and figure out how I really want to proceed!
When I was reading your second post, my thoughts echoed yours of using polyurethane foam instead of the polystyrene foam. The polystyrene is just so convenient to pick up at the hardware store, and...