Anyone know why this g17 comand causes a swooping dip in this tool path. The machine is a Dyna Myte 1007 and the post processor is for mach3. Fusion dosent have a specific post for my machine. All...
Type: Posts; User: funford
Anyone know why this g17 comand causes a swooping dip in this tool path. The machine is a Dyna Myte 1007 and the post processor is for mach3. Fusion dosent have a specific post for my machine. All...
Sent you a PM
This is the one I used. It worked great.
https://www.amazon.com/Gotek-SFR1M44-U100-1-44MB-Floppy-Emulator/dp/B0762NCHC6
I was trying to reach you about those spare parts but your inbox is full. Send me a PM with your phone# or email please.
I removed this line and the the G17 responded as expected. Going forward when I generate tool paths I make sure lead in and lead out are disabled and it will not use G18.
Weather was really nice this weekend so I decided to build a proper stand for DM1007.460026460028
Swoop-dive is a really good way to describe it. At first that G18 was the one I first suspected because it had the -Z movement. But that line is where the cutter drops to make the first pass. the...
Did you get a chance to do some more experimenting? I was using the Mach3Mill and for the most part it appears to work. However when I ran the code listed below it plunged the Z down about .25". I...
456030456032
Looking to source some backup Axis Control Cards. Anyone have anything?
I think I'm running 2.0, do you still need it?
Thanks for the advice, the initial plan was to go DOM and Floppy Emulator as you have suggested. I didn't at all consider the work offsets tool table and local edits. Part of this is due to my...
453826
453828
453830
So after some great info from Roberto from Dyna I was able to diagnose my issues to a bad AMC servo driver. Apparently you should always have a red led on the drives status light until the PLC...
Are the output measurements correct? Is E to Ov suppose to have voltage? I thought ov was neutral and e was earth ground. But have know idea if a transformer like this is suppose to read such.
Ohh the actual wires have been removed and replaced with drawn, so its easier to see.
There is two jumpers both the dark and light green in the first photo.
Sorry to ask such a simple question but I'm trying to cover all my basis. I have a new to me CNC mill with unknown history. It has a transformer that needs to be wired based on input voltage. It was...
Yes I'm definitely crazy. Do I need them? Probably not, I have ATC on my system but its probably going to be like the time I had to have a threading gearbox on my lathe and it took me an extra year...
Thanks Sun God I emailed the link on the site.
452658
- - - Updated - - -
452660
Yeah I have seen that before where the system will rarely tell you whats wrong with it. One error will give you many.
Not sure what control I have. This is whats in the cabinet and in the pc...
I'm going to do my best to the original control to work but it would seam there are some gremlins.
So rewiring the transformer fixed the resistor over heating and as suspected the voltage to the...
Hmm.... excess power ??, that lines up with the transformer being wired incorrectly. That's good news.
Well it didn't take long to run into some issues. First problem was the main enclosure fan. Soon as I gave it power it screeched so loud it up set the dog and he started howling. This was minor looks...
I think the travel is what its named after 1007 10x7 and I think 10 on the Z. From what I can tell from research its based on the 2800, the 2900 is the 2800 with tool changer and the 1007 is the 2900...
I picked up a nice little mill a while back and I finally got the time to dig into it. I'm pretty new to CNC mills so this should be and adventure. I have a CNC router and built a half dozen...
Geesh, I need to do a better job of reading looks like setlab already suggested changing the draw bar. Its a shame I have about 12studs but 50 holders I would be happy with 20 more but damn they...
Has anyone considered using the 2800 or 1007 itself with lathe tooling to make the studs?