translated for abtwiler00
" Hello What did they send him in the mail? Unfortunately, I can't get anywhere in exactly the same place.
Would be very grateful for their help. "
Type: Posts; User: Rich Carlstedt
translated for abtwiler00
" Hello What did they send him in the mail? Unfortunately, I can't get anywhere in exactly the same place.
Would be very grateful for their help. "
Thats it Leo !
You have it.
Hope there is some help for you there !
Rich
Leo, you mentioned Service bulletin.. There is a whole series of service bulletins
Let me look to see where they are
Rich
Leo, I hate to say it, but I had to do it for my KM3 machine when it developed memory issues
There are 81 pages on the website and I went back and looked at all 81 to find headings and information...
Thank You MacDave 73
Appreciate the magnificent work and pictures !
rich
if I recall correctly , the PC Max software also requires a Dongle in order to operate
I think Hurco did that to prevent copying the software ?
It may also need Win 95 or whatever ?
Did you do a...
All is well,
Hurco tech Service returned my call for help, and suggested that I do the following--which worked
There is a row of chips next to the battery slots, they are system chips (12 that are...
ANy help is appreciated
Since the original Memory Board did not work with the install of batteries and memory chips ( black Screen) I purchased a used memory board from eBay
I looked for a...
DJ, no plug found except for a 7 pin connector -looks like military
I do not have a keyboard , only digits for input
Thanks DJ .for the suggestion ... My machine does not have tape or disk drive so let me look into that.
Rich
My Hurco stopped working and said there was a memory failure , so I know that the Dallas chips ( which are original)
had failed , so I followed Bloke's advice and replaced the memory chips and...
Any Update ?
Rich
I had a spare power supply given to me for my KM3 , but it was defective so I gave it to a electronic technician to repair
in case i need it and after some time , he said to toss it as it was not...
Ray , not sure of your specifications with the UK version of the bridgeport
maybe this can help, My BP is a J head, 1962 model 4 step pulley
Spindle Speeds are 660,1115,1750,2720 RPM
Motor is a...
Just saw your post Mark
I have a Ultimax II and had some issues with the left monitor but got it fixed and posted here maybe 5-10 years ago
The right screen and left screen are different.. too...
Do you have Dallas Memory Chips?
https://www.cnczone.com/forums/hurco/279998-need-help-old-hurco-ultimax-ii.html
The old Hurcos had lots of problems with those chips ( lasted on;y 15 years)
...
On a Hurco ( KM3) the servo end of the screw has thrust bearings , thats all you need. the opposite end is just support bearings
If there is proper preload and the bearings are the correct ones (?)...
The spring is shot in the Kwik Switch Nut
You need to remove the set screw and take it off and replace the spring (s)
Rich
...
I get all my Kwik Switch tooling from Steve at
Tools-n-Gizmos: New and Used Machine Tooling
Awesome inventory of new and used .
No relations with vendor , just good service
Rich
That's a SM-1 ( ie Small Mill) which was the predecessor to the KM series ( ie Knee Mill) and dates around 1980 ( KM starts 1985 ?)
They are physically very close with 13 "Y and 24 " X ~ travel ...
With the number of modern control conversions going on, perhaps you could get some surplus boards from a convertor ?
They use to be listed on ebay a few years ago and maybe contact some on this...
I have not worked on a KM 1, but have a KM 3
The Control itself runs on single phase, so when I got my mill, I changed the wiring
My 220/240 single phase goes through the door switch and directly...
Charlie
Still have my Hurco, but it has been 20 years since I played with transferring programs
I am sure Bloke or others can answer the question more accurately
Hurco had a Software PC program...
Spectrumsas, if you follow Keenyjr's lead, it works
Click on TheGannsmann logo at the top of his post and it will lead to his website where you can contact him.
Skullworks old friend, I believe...
Green0.
I don't have an answer for your issue, because I don't know the machine- am not a Hurco Tech Rep -nor a active follower of this thread.
My observation is that you are not responsive to...
Bit late, but Jim answered it pretty well.
We did exactly what you are inquiring about making round dies for the plastic extrusion world
We used a Horizontal Boring mill as it gives the best...
You're right Bob, I havn't heard much about that level of success with Mach 3.
I am still running the original Randtronics and Hurco program and have the tool inventory filled with 30 tools or so....
The ears are not a good reference point. I mean they are close, but not perfect. I bored out a piece of 3 inch hex stock to match the spindle taper and have it on a granite block with a height gauge,...
You are getting it tight with that method !
Not done this on my Hurco, but when I was working, we had one tool that had a last word indicator mounted permanently ( No Spindle turns !)
and during...
I have Kwik 200's; for 19 years now and feel they are pretty stable.
I assume you mean removing a tool, and then returning that tool for same/similar use later
Two things affect the tool setting in...