pretty sure it's Next Generation Controller. and for the PP https://cam.autodesk.com/hsmposts ( if HSMWorks for CAM).
Type: Posts; User: countryguy
pretty sure it's Next Generation Controller. and for the PP https://cam.autodesk.com/hsmposts ( if HSMWorks for CAM).
Not sure it matters but I was just chatting w/ a guy today on a 98 and he needed the pre-NGC post processor for Fusion. Not the NGC one. Just a thought.
Hi - Couple things- I've never heard of an XM012 before... what tis this machine? And it might just be easier to repair the CPU board or 232 adapters (if used on this). If it's the...
No sure what you're exactly asking as which light or what the lables mean.. but we'll solve the No One part. :stickpoke TC is tool changer. The lights are covered in the Electrical Service...
post up the pics first is what I would do. Create a google drive or docs share for the pics and reply here w/ the link. I'll try to help you here (in the spirit of future knowledge for all) .
I've seen a few posts similar to this over the years- , and also others about 232 comms setup problems between PC and Haas in genreal. Proper Serial Comms setup and xmission settings from the Haas...
maybe something in this thread. Some solid seniority level posts. The conclusion and some steps seem in line with some of your notes.
https://tinyurl.com/2p87u58v
The temp sensor is located in a few spots I've seen. There is a metal clip where the sensor is pressed into. It's a PEPI sensor on many and you wont get them to respond or reply. I tried and...
Just so you see the wiring diagram and if you'll use the user Mcode relays (assume it has one?) . Just some 411
**Page 55 starts the I/O bd. Page 62, P22 is Skip plug. Page 74 shows the Probe...
Something that long, may need to consider adding Laser or Linear mag scale & encoder positioning. if I recall, there are notes and info out there sompleace on a Haas option. (I think I've seen...
Afternoon guys; to clarify my remarks, we run an air-dryer on the output too. a must. It was the closed system for lubrication fluid with the moisture filter and fluid filter that we had problems...
Sounds like a fun setup. We have the 30/60. the inrush is like 5amps on 240 single phase. Where do you have the wild-leg connected too? By that I mean the 240 VAC single-phase is passed thru the...
replied on your other PM post...
did you check the parms setting?
A floppy drive lets you add programs to the control and manage programs between ... Enable Parameter 209:21 FLOPPY ENABLED (set to 1).
It's pretty easy on our VF/4 you can do it.. but might as well just replace from Haas. I think it was $450 and no core charge. Then fix the old one as a spare? The drawbar pressure needs to be...
couple items - I sent you a PM. I'm in the garage too, with my kid. A few factors include inrush current, AC 240 or 120 capacity, CFM, and duty-cycle. (as least as we found out).
I...
https://www.haascnc.com/content/dam/haascnc/en/service/manual/service/english---vf-series-service-manual---2002.pdf
Page 354... Shows the output section .
Page 351 .... Shows the input
Cool post. I have a buddy w/ one of these types. Will remember this one. The AtoD must be an Analog to Digital calibration pot (capn obvious) that tweaks the reference voltage used when converting...
Evening, you may want to pop over to the Haas forum on practical machinist... There are several guys w/ a 92 and 93 machine. Its been a few years but my 98 VF 21 changer manual specifically notes...
Maybe this will help ?
https://www.haascnc.com/service/codes-settings.type=mcode.machine=mill.value=M21.html
https://www.cnczone.com/forums/haas-mills/63878-help-using-custom-m-codes-m-fin.html
https://staging-diy.haascnc.com/sites/default/files/Locked/Manuals/Service/1994/VMC_Service_Manual_96-8100_English_December_15_1994.pdf?0=%253F2651
Might be in here.
232 can get fussy - there are a number of testers both soft and hard ware provisioned.
Like:
https://www.stratusengineering.com/product/ez-tap/...
The tip a buddy gave me ... I put these between the machine drain the the tup... and it's a Haas VF/4 w/ the chip pan, but it still does not work that well compared to this. After a few sessions...
I am going to add on as I thought about this for our VF/ a bit. .we have Alexa, and I assume google devices have Equiv. if you have wifi and one of these services (Alexa or google) this might work?...
Hi JD... hope all is well over yonder~
To add on...
https://www.youtube.com/watch?v=CU26W8CXpeE
And a $7 phtoresistive relay assy looked neat-
https://tinyurl.com/esxybea2
yup... Most of the info is in here.
https://tinyurl.com/wcmbpxc
C41 if I recall. The -12 is 'derived' from a special RS232 capable IC. (all the tech goo is in my thread). And the small...
:-) yeah... Same thing on our side. Lot's of both type. Here is my short 3 cents. CME tools. I like them. Live not to far and drive up there. Have quite a bit from them. Use for knock...
REset all the cables and connections. All the way to the rear cab.
Here are some options for new encoders. Sub's houses are out there. I pulled a few recently. Contact them w/ your RENCO pn....
Looking forward to it. I was also considering a tool changer on the YMC. a 3 or 4 banger... and maybe using an Arduino and custom code/PIA (peripheral interface adapter) lines etc. some ALU and...
My interest is peeked! I upgraded a YMC to DC-AIO by centroid. We love it... for a knee mill. I do enjoy Centroid.. I'll admit that- Also have a 98 Haas we rebuilt but left the controls alone. ...