I am sending the question to Joakim. Will report back what I find.
Tnx!
Bruce
Type: Posts; User: bcavender
I am sending the question to Joakim. Will report back what I find.
Tnx!
Bruce
Mauri,
Thank you!!!
I had not noticed that selection in the Stock and Regions menu.
I defined a point, selected it with the command you suggested (thinking it might work like creating a...
Several years back, I noticed a thread that suggested the idea of being able to select a point where madCAM would begin a toolpath operation.
Was this ever implemented or is there another way to...
A friend has a 1640L with a CamLock system that holds the spindle to the head. He started to simply face a small bar and the entire spindle came off and fell.
I went over and we put it back on,...
Hi John,
I actually loosened the tool tolerance and it smoothed out 99% of the z variation. Turning on control points in Rhino helped visualize this greatly. Sky Greenwald had a helpful article...
The underlying reason behind the question was that on the MC post processing page there was a Home Position that I was trying to figure out its functionality. My system defaulted to 0.25", but I...
Tried that on my old copy of Rhino5 ... but still just had the Smileyface in the toolbar.
I have since upgraded to R6 and installed MC there and got back working again.
Appreciate the help!
B
Svenakela,
I appreciate the reply. Let me see if I have this straight by a practical example from a code snippet:
(M17Vgroove)
N100 G40 G56 G80 G90 G94
(Bullnose 60radius)
N101 G111...
I am roughing, then planar finishing a 2" diameter cylinder to a 1 in 10 tapered surface with a 1/2" bullnose mill with a 0.060" corner radius. The bull nose finished so-so with significant...
Been using madCAM with Rhino5 for a few weeks now with no problem. I reopened a file with toolpaths that needed a modification today and the madCAM toolbar was missing.
In Options-PlugIns in...
In my post processor I see:
*RAPID*
N"lnbr" G00 "x" "y" "z"
*END_SECTION*
*RAPID_APPROACH*
N"lnbr" "x" "y" "z"
*END_SECTION*
Tasdau,
Turned my first test using the buttress thread design using a 2" slug.
http://www.cnczone.com/forums/attachment.php?attachmentid=384900&stc=1
I started by off on the side of caution...
I have built a number of models with parallel surfaces that allow Upper and Lower curves to be successfully turned into features. Upper and lower guide values show up nicely in the wire simulations...
As a test, I loaded our Mits with the G-code you made from my threading tool model with MasterCAM. The geometry displayed perfectly on the screen and the part cut precisely ... first time!
VERY...
Tasdau,
Absolute U/V was not set on the machine. Have it set now. All the FeatureCAM posts were using G90s (Absolute). (I couldn't find any into in FCAM help that state U/V parameters are...
Tasdau,
Well, that is a BIG help after looking at your code. All your assumptions are good, except the last one I don't know about:
"You have 'Absolute UV' active in the switch screen (for the 4...
Tasdau,
Very interesting! Those items would be killer. It logically makes sense since they lie in my red flag zone between the correct looking sim in FeatureCAM and the Mitsubishi Controller...
Tasdau,
Awesome Text to MitsubishiLogo 3D geometry!
Heck, that is down right inspiring to this knuckledragger :^)
Very Nice Work!
I exported/zipped/attached an IGS of the model tuned...
Tasdau,
Thank you for your kind offer. Here is where I stand.
I made progress by learning/accomplishing the WireAlignment & Taper Initialization. The Z3 and Z4 numbers calculated were only a...
Msrblonlin,
Thank you for the suggestions.
I was finally able to figure out the Taper Initialization process after studying the Mitsubishi FA-S2 PDF for 3-4 days and calling around. The manual...
Mate,
After reading the FA-S machine PDF in depth, I found multiple references to a "Taper Initialization" procedure being recommended before attempting any work. Unfortunately the PDF doesn't have...
*****************************
Yep, I am holding at Win7 so far. Office2010 is the last MS non-subscription suite. I bought an copy off Ebay last month strangely enough ... and it runs fine. No...
SpaceClaim has a 1yr student edu license for $49, but lists a CAD seat for $4000.
Their videos are fabulously impressive for editing models, but $49 is essentially free like Fusion360. They are...
Datac,
We are on the same wavelength between Risk a lot of money/data/future survivability and Smarter than Free. You nailed the student/artisan/retired engineer market that the industry has...
Thanks for responding Louie!
What terms were you able to purchase SpaceClaim for and what was the price?
Tnx!
Bruce
Hello Mate,
I do appreciate the steering points to go looking for.
The G-code is posting out of FeatureCAM. One comment I got from others was that others who tried to do tapers in the shop had...
Hello,
I am having two problems with cutting a Buttress thread lathe tool out of a 3/8”x3/8”x3” HSS tool blank on a Mitsubishi FA-S wire machine using the 4th axis. The front and side relief...
Hi KH0UJ,
Very interesting comment on SketchUp! I never had taken the time to look at it and was unaware there were CAM plugs that Sketchup could be extended with.
What is the CAM plug in did...
Bostosh,
Very nice product work there! You clearly have put in some time to get this point. Kudos!
I am exactly with you. It seems that 75% of CADCAM producers aim to tap and drain the large...
Sounds like your customers could end up getting you into multiple subscription situations if I understood you correctly. I guess it's all good if they are paying for you to support that for them....